ZVD Zavod za varstvo pri delu d.o.o.
OB05-36 Izdaja / Revision: 12 Stran / Page: 1 / 4
Reg. št. / Ref. No.: 3150-0004/17-0003
Velja od / Valid as of: 4. september 2023
Zamenjuje izdajo, veljavno od dne / Replaces the Annex valid as of: 14. april 2023
Akreditacija je veljavna do preklica. Veljavnost je mogoče preveriti na spletni strani SA, www.slo-akreditacija.si.
This accreditation shall remain in force until withdrawn. Information on current status is available at the SA website, www.s lo-akreditacija.si.
PRILOGA K AKREDITACIJSKI LISTINI
Annex to Accreditation Certificate
CP-018
1 AKREDITIRANI ORGAN / Accredited Body
ZVD Zavod za varstvo pri delu d.o.o.
Pot k izviru 6, 1260 Ljubljana - Polje
2 ZAHTEVE ZA USPOSOBLJENOST / Competence Requirements
SIST EN ISO/IEC 17065:2012
Dodatne zahteve, ki veljajo za nekatere vrste ugotavljanja skladnosti, so opredeljene v podrobnem opisu
obsega akreditacije za to vrsto ugotavljanja skladnosti, v poglavju 3.2. / Additional requirements applicable
to certain types of conformity assessment are defined in the detailed description of accreditation scope for
this type of conformity assessment, under 3.2.
3 OBSEG AKREDITACIJE / Scope of accreditation
V okviru te akreditacijske listine Slovenska akreditacija priznava akreditiranemu organu usposobljenost
za opravljanje naslednjih dejavnosti: / SA hereby recognizes the accredited body as being competent to
perform the following activities:
3.1 Skrajšan opis obsega akreditacije / Brief description of the scope
Certificiranje proizvodov: certificiranje na podlagi tipskega preskusa proizvoda: osebna varovalna
oprema za zaščito rok
Certification of products: type testing certification: personal protective equipment for hands
Akreditacija za namen priglasitve: Direktiva 2014/33/EU
Priloga k akreditacijski listini
Annex to Accreditation Certificate CP-018
Velja od / Valid as of 4. september 2023
Zamenjuje izdajo, veljavno od dne / Replaces the Annex valid as of 14. april 2023
Akreditacija je veljavna do preklica. Veljavnost preveriti na
This accreditation shall remain in force until withdrawn.
Information on current status available at
www.slo-akreditacija.si
OB05-36 Izdaja / Revision: 12 Stran / Page: 2 / 4
Accreditation for notification purposes: Directive 2014/33/EU
Priloga k akreditacijski listini
Annex to Accreditation Certificate CP-018
Velja od / Valid as of 4. september 2023
Zamenjuje izdajo, veljavno od dne / Replaces the Annex valid as of 14. april 2023
Akreditacija je veljavna do preklica. Veljavnost preveriti na
This accreditation shall remain in force until withdrawn.
Information on current status available at
www.slo-akreditacija.si
Pot k izviru 6, 1260 Ljubljana – Polje
OB05-36 Izdaja / Revision: 12 Stran / Page: 3 / 4
3.2 Podroben opis obsega akreditacije / Detailed scope of accreditation
3.2.1 Pot k izviru 6, 1260 Ljubljana – Polje
Certificiranje proizvodov / Certification of products
Tabela / Table 1 – Osebna varovalna oprema / Personal protective equipment
Certificiranje v skladu s shemo / Certification in accordance with the scheme: Certificiranje na podlagi tipskega preskusa proizvoda
(modul B, Uredba (EU) 2016/425) skladno s shemo ND-CO-05 / Type testing certification (Module B, Regulation (EU) 2016/425) in
accordance with the scheme ND-CO-05
Tip obsega: fiksni / Type of scope: fixed
Št.
No.
Materiali oz. proizvodi
Materials or Products
Oznaka standarda ali normativnega dokumenta
(v celoti ali delno)
Reference to standard or normative document
(entirely or partly)
Naslov standarda ali normativnega dokumenta v
celoti oz. delno (npr. poglavje, del, točka)
Title of standard or normative document entirely or
partly (e.g. part, chapter, article)
Osebna varovalna oprema za zaščito rok
Personal protective equipment for hands
1. Varovalne rokavice za
zaščito rok pred toplotnimi
tveganji (toplote in/ali
ognja)
Protective gloves against
thermal risks (heat and/or
fire)
SIST EN 407:2020 Varovalne rokavice in druga oprema za zaščito rok
pred toplotnimi tveganji (toplote in/ali ognja)
Protective gloves and other hand protective
equipment against thermal risks (heat and/or fire)
2. Varovalne rokavice za
zaščito pred mehanskimi
tveganji
Protective gloves against
mechanical risks
SIST EN 388:2016
SIST EN 388:2016/A1:2019
Rokavice za zaščito pred mehanskimi tveganji
Protective gloves against mechanical risks
3. Varovalne rokavice za
varilce
Protective gloves for
welders
SIST EN 12477:2002
SIST EN 12477:2002/A1:2005
Varovalne rokavice za varilce
Protective gloves for welders
4. Varovalne rokavice
Protective gloves
SIST EN ISO 21420:2020 Varovalne rokavice - Splošne zahteve in preskusne
metode
Protective gloves - General requirements and test
methods (ISO 21420:2020)
5. Varovalne rokavice za
zaščito pred mrazom
Protective gloves against
cold
SIST EN 511:2006 Rokavice za zaščito pred mrazom
Protective gloves against cold
Priloga k akreditacijski listini
Annex to Accreditation Certificate CP-018
Velja od / Valid as of 4. september 2023
Zamenjuje izdajo, veljavno od dne / Replaces the Annex valid as of 14. april 2023
Akreditacija je veljavna do preklica. Veljavnost preveriti na
This accreditation shall remain in force until withdrawn.
Information on current status available at
www.slo-akreditacija.si
Pot k izviru 6, 1260 Ljubljana – Polje
OB05-36 Izdaja / Revision: 12 Stran / Page: 4 / 4
Akreditacija za namen priglasitve / Accreditation for notification purposes
Tabela / Table 2 – Dvigala / Lifts
Dodatne zahteve za usposobljenost / Additional requirements for competence: Direktiva 2014/33/EU / Directive 2014/33/EU
Certificiranje v skladu s shemo / Certification in accordance with scheme: Certificiranje na podlagi preverjanja enote za dvigala skladno s
shemo ND-CO-06 R2 / Certification based on unit verification for lifts in accordance with the scheme ND-CO-06 R2
Tip obsega: fiksni / Type of scope: fixed
Št.
No.
Družina proizvodov, proizvod /
predvidena uporaba / nabor izdelkov
Product family, product / Intended use /
Product range
Postopek / Moduli
Procedure / Modules
Priloge ali členi direktive / uredbe
Annexes or articles of the Directive /
Regulation
6. Dvigala
Lifts
Modul G
Module G
Priloga VIII
Annex VIII
Lokacije v tujini, vključene v obseg akreditacije / Foreign locations included under the accreditation:
− ni relevantno / not relevant
Datum / Date: 4.9.2023 Direktor / Director
Dr. Boštjan Godec
Kopija priloge k akreditacijski listini za objavo na spletnem mestu.
Podpisani original priloge na vpogled na sedežu SA.
Copy of Annex to the accreditation certificate for web publishing.
Signed original of Annex available for consultation at the SA head office.
KNT d.o.o.
OB05-32 Izdaja / Revision: 8 Stran / Page: 1 / 3
Reg. št. / Ref. No.: 3150-0005/16-0004
Velja od / Valid as of: 12. december 2023
Zamenjuje izdajo, veljavno od dne / Replaces the Annex valid as of: 28. februar 2023
Akreditacija je veljavna do preklica. Veljavnost je mogoče preveriti na spletni strani SA, www.slo-akreditacija.si.
This accreditation shall remain in force until withdrawn. Information on current status is available at the SA website, www.s lo-akreditacija.si.
PRILOGA K AKREDITACIJSKI LISTINI
Annex to Accreditation Certificate
LK-038
1 AKREDITIRANI ORGAN / Accredited body
KNT d.o.o.
Kidričeva cesta 51, 4220 Škofja Loka
2 ZAHTEVE ZA USPOSOBLJENOST / Competence Requirements
SIST EN ISO/IEC 17025:2017
3 OBSEG AKREDITACIJE / Scope of accreditation
V okviru te akreditacijske listine Slovenska akreditacija priznava akreditiranemu organu usposobljenost
za opravljanje naslednjih dejavnosti: / SA hereby recognizes the accredited body as being competent to
perform the following activities:
3.1 Skrajšan opis obsega akreditacije / Brief description of the scope
Kalibriranje na naslednjih področjih in naštetih pod-področjih / Calibration in the following fields and the
specified sub-fields:
o MEHANSKE VELIČINE / MECHANICAL QUANTITIES:
• Tlak / Pressure: (podtlak, nadtlak, razlika tlakov pri atmosferskem tlaku / Negative pressure
gauge, Positive pressure gauge, Pressure difference at atmospheric pressure)
Priloga k akreditacijski listini
Annex to Accreditation Certificate LK-038
Velja od / Valid as of 12. december 2023
Zamenjuje izdajo, veljavno od dne / Replaces the Annex valid as of 28. februar 2023
Akreditacija je veljavna do preklica. Veljavnost preveriti na
This accreditation shall remain in force until withdrawn.
Information on current status available at
www.slo-akreditacija.si
KNT d.o.o., Kidričeva cesta 51, 4220 Škofja Loka
OB05-32 Izdaja / Revision: 8 Stran / Page: 2 / 3
3.2 Podroben opis obsega akreditacije / Detailed scope of accreditation
3.2.1 KNT d.o.o., Kidričeva cesta 51, 4220 Škofja Loka
Tabela / Table 1 – Kalibracije v laboratoriju / In-lab calibrations
Št.
No.
Merjena veličina,
(pod)področje, oz. merilni
instrumenti in/ali območje
(merjene veličine).
Measured quantity,
(sub-)field, and/or
instruments, and/or range
(of measured quantity).
Območje (merjene veličine)
ali
Omejitve, pogoji, vplivne
veličine.***
Range (of measured quantity)
or
Limitations, conditions,
influence quantity.***
Kalibracijska in merilna
zmogljivost (CMC)
izražena kot razširjena
negotovost.*
Calibration and
measurement Capability
(CMC) Expressed as an
Expanded Uncertainty.*
- Tip kalibracijske metode (opcija)
- Kalibracijski postopek
- Merilni instrumenti (opcija)**
- Opombe
- Type of calibration method (option),
- Internal calibration procedure
- Measuring instruments (option)**
- Remarks
MEHANSKE VELIČINE
MECHANICAL QUANTITIES
Tlak
Pressure
Podtlak
Negative pressure gauge
interni postopek / internal procedure, ki
temelji na / based on: EURAMET / Cg-17/
v4.1 / 09/2022
1.
(-95 do/to -7) kPa 200 Pa
Medij: plin
Medium: gas
mehanski in elektromehanski manometri
Mechanical and electromechanical
manometers
2. -7 kPa do/to -200 Pa 7,5 Pa
3. (-200 do/to 0) Pa 3 Pa
Nadtlak
Positive pressure gauge
interni postopek / internal procedure, ki
temelji na / based on: EURAMET / Cg-17/
v4.1 / 09/2022
4. 0 Pa do/to 2 kPa 3 Pa Medij: plin
Medium: gas
mehanski in elektromehanski manometri
Mechanical and electromechanical
manometers
5. (2 do/to 7) kPa 7,5 Pa
6. 7 kPa do/to 1 MPa 250 Pa
7. (1 do/to 2) MPa 500 Pa
8. (2 do/to 4) MPa 1000 Pa
Priloga k akreditacijski listini
Annex to Accreditation Certificate LK-038
Velja od / Valid as of 12. december 2023
Zamenjuje izdajo, veljavno od dne / Replaces the Annex valid as of 28. februar 2023
Akreditacija je veljavna do preklica. Veljavnost preveriti na
This accreditation shall remain in force until withdrawn.
Information on current status available at
www.slo-akreditacija.si
KNT d.o.o., Kidričeva cesta 51, 4220 Škofja Loka
OB05-32 Izdaja / Revision: 8 Stran / Page: 3 / 3
Tabela / Table 2 – Kalibracije na terenu / On-field calibrations
št.
Item
no.
Merjena veličina,
(pod)področje, oz.
merilni instrumenti
in/ali območje
(merjene veličine).
Measured quantity,
(sub-) field, and/or
instruments, and/or
range (of measured
quantity).
Območje (merjene
veličine) ali
Omejitve, pogoji,
vplivne veličine.***
Range (of measured
quantity) or
Limitations, conditions,
influence quantity.***
Kalibracijska in
merilna
zmogljivost (CMC)
izražena kot
razširjena
negotovost
(Calibration and
measurement
Capability (CMC)
Expressed as an
Expanded
Uncertainty)*
- Tip kalibracijske metode (opcija)
- Kalibracijski postopek
- Merilni instrumenti (opcija)**
- Opombe
- Type of calibration method (option),
- Internal calibration procedure
- Measuring instruments (option)**
- Remarks
TLAK
Pressure
Podtlak
Negative pressure gauge
interni postopek / internal procedure, ki
temelji na / based on: EURAMET / Cg-17/
v4.1 / 09/2022
9. (-95 do/to -7) kPa 200 Pa Medij: plin
Medium: gas
mehanski in elektromehanski manometri
Mechanical and electromechanical
manometers
10. (-7 do/to 0) kPa 7,5 Pa
Nadtlak
Positive pressure gauge
interni postopek / internal procedure, ki
temelji na / based on: EURAMET / Cg-17/
v4.1 / 09/2022
11. (0 do/to 7) kPa 7,5 Pa Medij: plin
Medium: gas
mehanski in elektromehanski manometri
Mechanical and electromechanical
manometers
12. 7 kPa do/to 1 MPa 250 Pa
13. (1 do/to 2) MPa 500 Pa
14. (2 do/to 4) MPa 1000 Pa
Opombe / Notes:
* CMC opomba / CMC Note
Razširjena negotovost je podana kot kombinirana standardna negotovost pomnožena s takšnim faktorjem pokritja k, da določa interval
zaupanja približno 95 %. / Expanded uncertainty of measurement is stated as the standard uncertainty of measurement multiplied by the
coverage factor k such that the coverage probability corresponds to approximately 95 %.
** Navedba informacije o merilnih instrumentih se v tej koloni uporabi le v tistih primerih, kjer to ne izhaja že iz opredelitve veličine, opisa
(pod)področja in instrumentov v drugi koloni tabele. / Information on measuring instruments are specified in this column only if it is not clear
from the description of quantity, (sub-) field, and/or instruments in the second column of this table.
*** Kadar je za enoumno razumevanje zmogljivosti potreben opis robnih pogojev, vplivnih veličin ali drugih omejitev, se ti navaja jo v tej koloni (z
enoumno oznako kolone), območje merjene veličine pa je v takem primeru določeno že v drugi koloni te tabele. / When a description of the
boundary conditions, influence quantity or other limits is required for an unequivocal understanding of capabilities it is specified in this column
(clearly indicated), providing that the range of measured quantity is defined in the second column of this table.
Datum / Date: 12. 12. 2023 Direktor / Director
Dr. Boštjan Godec
Kopija priloge k akreditacijski listini za objavo na spletnem mestu.
Podpisani original priloge na vpogled na sedežu SA.
Copy of Annex to the accreditation certificate for web publishing.
Signed original of Annex available for consultation at the SA head office.
TKC Tehnološki konzultantski center d.o.o.
OB05-25 Izdaja / Revision: 8 Stran / Page: 1 / 3
Reg. št. / Ref. No.: 3150-0012/12-0011
Velja od / Valid as of: 3. februar 2023
Zamenjuje izdajo, veljavno od dne / Replaces the Annex valid as of: 5. maj 2022
Akreditacija je veljavna do preklica. Veljavnost je mogoče preveriti na spletni strani SA, www.slo-akreditacija.si.
This accreditation shall remain in force until withdrawn. Information on current status is available at the SA website, www.slo-akreditacija.si.
PRILOGA K AKREDITACIJSKI LISTINI
Annex to Accreditation Certificate
LP-110
1 AKREDITIRANI ORGAN / Accredited body
TKC Tehnološki konzultantski center d.o.o.
Trnovska ulica 8, 1000 Ljubljana
2 ZAHTEVE ZA USPOSOBLJENOST / Competence Requirements
SIST EN ISO/IEC 17025:2017
3 OBSEG AKREDITACIJE / Scope of accreditation
V okviru te akreditacijske listine Slovenska akreditacija priznava akreditiranemu organu usposobljenost
za opravljanje naslednjih dejavnosti: / SA hereby recognizes the accredited body as being competent to
perform the following activities:
3.1 Skrajšan opis obsega akreditacije / Brief description of the scope
Področja preskušanja glede na vrsto preskušanja / Testing fields with reference to the type of test:
• mehansko preskušanje / mechanical testing
Področja preskušanja glede na vrsto preskušanca / Testing fields with reference to the type of test item:
• industrijski materiali in proizvodi / industrial materials and products
Na podlagi odločitve št. 3151-0065/22-0033 so akreditiranemu organu začasno odvzete pravice iz
akreditacije za obseg akreditacije, ki je v poglavju 3.2 osenčen in prečrtan. / Based on Decision
no. 3151-0065/22-0033, SA has suspended the accredited CAB’s rights deriving from
accreditation for the scope of accreditation that is shaded and crossed-out in Chapter 3.2.
Priloga k akreditacijski listini
Annex to Accreditation Certificate LP-110
Velja od / Valid as of 3. februar 2023
Zamenjuje izdajo, veljavno od dne / Replaces the Annex valid as of 5. maj 2022
Akreditacija je veljavna do preklica. Veljavnost preveriti na
This accreditation shall remain in force until withdrawn.
Information on current status available at
www.slo-akreditacija.si
TKC d.o.o., Litostrojska cesta 60, 1000 Ljubljana
OB05-25 Izdaja / Revision: 8 Stran / Page: 2 / 3
3.2 Podroben opis obsega akreditacije / Detailed scope of accreditation
3.2.1 TKC d.o.o., Litostrojska cesta 60, 1000 Ljubljana
Tabela / Table 1
Tip obsega: fiksni / Type of scope: fixed
Mesto izvajanja: v laboratoriju / Site: in the laboratory
Področja preskušanja glede na vrsto preskušanja: mehansko preskušanje / Testing fields with reference to the type of test: mechanical
testing
Področja preskušanja glede na vrsto preskušanca: industrijski materiali in proizvodi / Testing fields with reference to the type of test
item: industrial materials and products
Št.
No.
Oznaka dokumenta,
ki opisuje metodo
preskušanja
Identification of the
document, describing the
testing method
Preskušana lastnost
oziroma parameter
Characteristic or
parameter tested
Opredelitev preskusa
(vrsta, princip oziroma
tehnika preskusa)
Description of test
(type of test, test principle or
technique)
Območje
preskušanja
Range of testing
Preskušanci
(materiali,
proizvodi)
Items tested
(materials,
products)
1. SIST EN ISO 17639:2013
točka 3.1
chapter 3.1
- Dimenzije
- Napake
- Makrostrukturne
značilnosti
- Dimensions
- Irregularities
- Macrostructural
characteristic
Makroskopska preiskava
zvarov
Macroscopic examination of
welds
(0 – 50)-kratna
povečava
(0 – 50)-magnification
zvari kovinskih
materialov
welds in metallic
materials
2. SIST EN ISO 148-1:2017 Udarna žilavost
Impact toughness
Udarni preizkus po
Charpyju
Charpy pendulum impact
test
od +20 do –60 °C
(0 – 300) J kovinski materiali
metallic materials
3. SIST EN ISO 9016:2013 Udarna žilavost
Impact toughness
Udarni preizkus po
Charpyju
Charpy pendulum impact
test
od +20 do –60 °C
(0 – 300) J zvari kovinskih
materialov
welds in metallic
materials
4. SIST EN ISO 7438:2021 Sposobnost deformacije;
ugotavljanje napak
Ability to undergo
deformation; determination
of imperfections
Upogibni preskus
Bend test
(0 – 180) ° kovinski materiali
metallic materials
5. SIST EN ISO 5173:2010
SIST EN ISO
5173:2010/A1:2013
Sposobnost deformacije;
ugotavljanje napak
Ability to undergo
deformation; determination
of imperfections
Upogibni preskus
Bend test
(0 – 180) ° zvari kovinskih
materialov
welds in metallic
materials
6. SIST EN ISO 9017:2018 Določanje nepravilnosti
(poroznosti, razpoke,
nespojena in neprevarjena
mesta, vključki)
Determination of
imperfections (porosities,
cracks, lack of fusion, lack
of penetration, inclusions)
Prelomni preskus
Fracture test
zvari kovinskih
materialov
welds in metallic
materials
7. SIST EN ISO 6507-1:2018 Trdota po Vickersu
Vickers hardness
Preskus trdote po Vickersu
Vickers hardness test
HV 10
kovinski materiali
metallic materials
Priloga k akreditacijski listini
Annex to Accreditation Certificate LP-110
Velja od / Valid as of 3. februar 2023
Zamenjuje izdajo, veljavno od dne / Replaces the Annex valid as of 5. maj 2022
Akreditacija je veljavna do preklica. Veljavnost preveriti na
This accreditation shall remain in force until withdrawn.
Information on current status available at
www.slo-akreditacija.si
TKC d.o.o., Litostrojska cesta 60, 1000 Ljubljana
OB05-25 Izdaja / Revision: 8 Stran / Page: 3 / 3
Tip obsega: fiksni / Type of scope: fixed
Mesto izvajanja: v laboratoriju / Site: in the laboratory
Področja preskušanja glede na vrsto preskušanja: mehansko preskušanje / Testing fields with reference to the type of test: mechanical
testing
Področja preskušanja glede na vrsto preskušanca: industrijski materiali in proizvodi / Testing fields with reference to the type of test
item: industrial materials and products
Št.
No.
Oznaka dokumenta,
ki opisuje metodo
preskušanja
Identification of the
document, describing the
testing method
Preskušana lastnost
oziroma parameter
Characteristic or
parameter tested
Opredelitev preskusa
(vrsta, princip oziroma
tehnika preskusa)
Description of test
(type of test, test principle or
technique)
Območje
preskušanja
Range of testing
Preskušanci
(materiali,
proizvodi)
Items tested
(materials,
products)
8. SIST EN ISO 9015-1:2012 Trdota po Vickersu
Vickers hardness
Preskus trdote po Vickersu
Vickers hardness test
HV 10
obločno varjeni
spoji
arc welded joints
9. SIST EN ISO 4136:2013 Natezna trdnost
(Fm, Rm)
Tensile strength (Fm, Rm)
Prečni natezni preskus
Transverse tensile testing
(0 - 400) kN
kovinski materiali
metallic materials
zvari kovinskih
materialov
welds in metallic
materials
Opombe / Notes:
• V vseh točkah podrobnega obsega akreditacije, pri katerih v rubriki "Območje preskušanja" ni navedenih podatkov, veljajo določila
posameznih standardov oziroma drugih javno dostopnih dokumentov, ki opisujejo metodo.
In all columns of the scope of accreditation where the cells under "Range of testing" are empty, the provisions of the relevant standards or
other publicly available documents describing testing methods should apply.
Datum / Date: 3.2.2023 Direktor / Director
Dr. Boštjan Godec
Kopija priloge k akreditacijski listini za objavo na spletnem mestu.
Podpisani original priloge na vpogled na sedežu SA.
Copy of Annex to the accreditation certificate for web publishing.
Signed original of Annex available for consultation at the SA head office.
PRIGO tehnični pregledi d.o.o.
OB05-31 Izdaja / Revision: 9 Stran / Page: 1 / 2
Reg. št. / Ref. No.: 3150-0019/15-0003
Velja od / Valid as of: 28. februar 2024
Zamenjuje izdajo, veljavno od dne / Replaces the Annex valid as of: 1. februar 2023
Akreditacija je veljavna do preklica. Veljavnost je mogoče preveriti na spletni strani SA, www.slo-akreditacija.si.
This accreditation shall remain in force until withdrawn. Information on current status is available at the SA website, www.slo-akreditacija.si.
PRILOGA K AKREDITACIJSKI LISTINI
Annex to Accreditation Certificate
K-147
1 AKREDITIRANI ORGAN / Accredited body
PRIGO tehnični pregledi d.o.o.
Podpeška cesta 10, 1351 Brezovica pri Ljubljani
2 ZAHTEVE ZA USPOSOBLJENOST / Competence Requirements
SIST EN ISO/IEC 17020:2012, tip C / type C
3 OBSEG AKREDITACIJE / Scope of accreditation
V okviru te akreditacijske listine Slovenska akreditacija priznava akreditiranemu organu usposobljenost
za opravljanje naslednjih dejavnosti: / SA hereby recognizes the accredited body as being competent to
perform the following activities:
3.1 Skrajšan opis obsega akreditacije / Brief description of the scope
• Kontrola zapisovalne opreme v cestnem prometu (tahografi) / Inspection of recording equipment in
road transport (tachographs)
Priloga k akreditacijski listini
Annex to Accreditation Certificate K-147
Velja od / Valid as of 28. februar 2024
Zamenjuje izdajo, veljavno od dne / Replaces the Annex valid as of 1. februar 2023
Akreditacija je veljavna do preklica. Veljavnost preveriti na
This accreditation shall remain in force until withdrawn.
Information on current status available at
www.slo-akreditacija.si
Kontrolni organ, PE Brdo, Mladinska ulica 89, 1000 Ljubljana
OB05-31 Izdaja / Revision: 9 Stran / Page: 2 / 2
3.2 Podroben opis obsega akreditacije / Detailed scope of accreditation
3.2.1 Kontrolni organ, PE Brdo, Mladinska ulica 89, 1000 Ljubljana
Tabela / Table 1
Tip obsega: fiksni / Type of scope: fixed
Št.
No.
Predmet kontrole
(proizvod, storitev, proces)
Item of inspection
(product, service, process)
Vrsta kontrole
Inspection type
Metode in postopki
(normativni dokumenti, interni
postopki)
Methods and procedures
(normative documents, internal
procedures)
Opombe
Notes
1. Zapisovalna oprema v
cestnem prometu -
analogni tahograf
- pred namestitvijo
- ob namestitvi
- redna
- med uporabo
Uredba (EU) št. 165/2014
Evropskega parlamenta in Sveta z
dne 4. februarja 2014 o tahografih v
cestnem prometu, Priloga I,
poglavje III(f) in VI
Pravilnik o odobritvi in nalogah
delavnic za tahografe in naprave za
omejevanje hitrosti (Ur. list RS, št.
24/19, 184/20, 163/21, 15/22), čl. 5
do 16
Kontrola z metodo:
- na prosto vrtečih valjih
- na merilni stezi dolžine
20 m
2. Zapisovalna oprema v
cestnem prometu -
digitalni tahograf
- pred namestitvijo
- ob namestitvi
- redna
- med uporabo
Uredba Sveta (EGS) 3821/85 o
tahografu (nadzorni napravi) v
cestnem prometu, Priloga IB,
poglavje III, točke 2.1, 2.2 in 3 in
poglavje VI
Pravilnik o odobritvi in nalogah
delavnic za tahografe in naprave za
omejevanje hitrosti (Ur. list RS, št.
24/19, 184/20, 163/21, 15/22), čl. 5
do 16
Kontrola z metodo:
- na prosto vrtečih valjih
- na merilni stezi dolžine
20 m
3. Zapisovalna oprema v
cestnem prometu -
pametni tahograf
- pred namestitvijo
- ob namestitvi
- redna
- med uporabo
Izvedbena Uredba Komisije (EU)
2016/799 z dne 18. marca 2016 o
izvajanju Uredbe (EU) št. 165/2014
Evropskega parlamenta in Sveta za
določitev zahtev glede konstrukcije,
preskušanja, namestitve, delovanja
in popravila tahografov in njihovih
sestavnih delov, Priloga IC,
poglavja 3.2, 3.3 in 6.
Pravilnik o odobritvi in nalogah
delavnic za tahografe in naprave za
omejevanje hitrosti (Ur. list RS, št.
24/19, 184/20, 163/21, 15/22), čl. 5
do 16
Kontrola z metodo:
- na prosto vrtečih valjih
- na merilni stezi dolžine
20 m
Datum / Date: 28.2.2024 Direktor / Director
dr. Boštjan Godec
Kopija priloge k akreditacijski listini za objavo na spletnem mestu.
Podpisani original priloge na vpogled na sedežu SA.
Copy of Annex to the accreditation certificate for web publishing.
Signed original of Annex available for consultation at the SA head office.
HIDROTEHNIK d.o.o.
OB05-25 Izdaja / Revision: 8 Stran / Page: 1 / 3
Reg. št. / Ref. No.: 3150-0015/21-0003
Velja od / Valid as of: 30. avgust 2023
Zamenjuje izdajo, veljavno od dne / Replaces the Annex valid as of: 24. januar 2023
Akreditacija je veljavna do preklica. Veljavnost je mogoče preveriti na spletni strani SA, www.slo-akreditacija.si.
This accreditation shall remain in force until withdrawn. Information on current status is available at the SA website, www.s lo-akreditacija.si.
PRILOGA K AKREDITACIJSKI LISTINI
Annex to Accreditation Certificate
LP-125
1 AKREDITIRANI ORGAN / Accredited body
HIDROTEHNIK d.o.o.
Slovenčeva ulica 97, 1000 Ljubljana
2 ZAHTEVE ZA USPOSOBLJENOST / Competence Requirements
SIST EN ISO/IEC 17025:2017
3 OBSEG AKREDITACIJE / Scope of accreditation
V okviru te akreditacijske listine Slovenska akreditacija priznava akreditiranemu organu usposobljenost
za opravljanje naslednjih dejavnosti: / SA hereby recognizes the accredited body as being competent to
perform the following activities:
3.1 Skrajšan opis obsega akreditacije / Brief description of the scope
Področja preskušanja glede na vrsto preskušanja / Testing fields with reference to the type of test:
• fizikalno preskušanje / physical testing
Na podlagi odločitve št. 3151-0229/22-0004 so akreditiranemu organu začasno odvzete pravice iz
akreditacije za obseg akreditacije, ki je v poglavju 3.2 osenčen in prečrtan. / Based on Decision
no. 3151-0229/22-0004, SA has suspended the accredited CAB’s rights deriving from
accreditation for the scope of accreditation that is shaded and crossed-out in Chapter 3.2.
Priloga k akreditacijski listini
Annex to Accreditation Certificate LP-125
Velja od / Valid as of 30. avgust 2023
Zamenjuje izdajo, veljavno od dne / Replaces the Annex valid as of 24. januar 2023
Akreditacija je veljavna do preklica. Veljavnost preveriti na
This accreditation shall remain in force until withdrawn.
Information on current status available at
www.slo-akreditacija.si
OB05-25 Izdaja / Revision: 8 Stran / Page: 2 / 3
Področja preskušanja glede na vrsto preskušanca / Testing fields with reference to the type of test item:
• gradbeni proizvodi, materiali in konstrukcije / construction products,material and structures
Priloga k akreditacijski listini
Annex to Accreditation Certificate LP-125
Velja od / Valid as of 30. avgust 2023
Zamenjuje izdajo, veljavno od dne / Replaces the Annex valid as of 24. januar 2023
Akreditacija je veljavna do preklica. Veljavnost preveriti na
This accreditation shall remain in force until withdrawn.
Information on current status available at
www.slo-akreditacija.si
Laboratorij za izvajanje tlačnih preizkusov, Slovenčeva ulica 97, 1000 Ljubljana
OB05-25 Izdaja / Revision: 8 Stran / Page: 3 / 3
3.2 Podroben opis obsega akreditacije / Detailed scope of accreditation
3.2.1 Laboratorij za izvajanje tlačnih preizkusov, Slovenčeva ulica 97, 1000 Ljubljana
Tabela / Table 1
Tip obsega: fiksni / Type of scope: fixed
Mesto izvajanja: na terenu / Site: fieldwork
Področja preskušanja glede na vrsto preskušanja: fizikalno preskušanje / Testing fields with reference to the type of test: physical
testing
Področja preskušanja glede na vrsto preskušanca: gradbeni proizvodi,materiali in konstrukcije / Testing fields with reference to the type
of test item: construction products,material and structures
Št.
No.
Oznaka dokumenta,
ki opisuje metodo
preskušanja
Identification of the
document, describing the
testing method
Preskušana lastnost
oziroma parameter
Characteristic or
parameter tested
Opredelitev preskusa
(vrsta, princip oziroma
tehnika preskusa)
Description of test
(type of test, test principle or
technique)
Območje
preskušanja
Range of testing
Preskušanci
(materiali,
proizvodi)
Items tested
(materials,
products)
1. SIST EN 805:2000
točka 11
point 11
Tesnost
Tightness
Tlačni preskus
Pressure test
Vodovodne cevi
in sistemi
Water supply
pipelines and
systems
2. SIST EN 12327:2013 Tesnost
Tightness
Tlačni preskus z zrakom
Pressure test with air
Cevni vodi
Pipellines
3. SIST EN 16932-3:2018
točka 12
point 12
Tesnost
Tightness
Tlačni preskus
Pressure test
Cevni vodi
vakumski jaški
Vakuum
pipelines
manholes
Opombe / Notes:
• V vseh točkah podrobnega obsega akreditacije, pri katerih v rubriki "Območje preskušanja" ni navedenih podatkov, veljajo določila
posameznih standardov oziroma drugih javno dostopnih dokumentov, ki opisujejo metodo.
In all columns of the scope of accreditation where the cells under "Range of testing" are empty, the provisions of the relevant standards or
other publicly available documents describing testing methods should apply.
Datum / Date: 30. avgust 2023 Direktor / Director
Dr. Boštjan Godec
Kopija priloge k akreditacijski listini za objavo na spletnem mestu.
Podpisani original priloge na vpogled na sedežu SA.
Copy of Annex to the accreditation certificate for web publishing.
Signed original of Annex available for consultation at the SA head office.
Branko Zorin s.p.
OB05-31 Izdaja / Revision: 8 Stran / Page: 1 / 2
Reg. št. / Ref. No.: 3150-0123/10-0011
Velja od / Valid as of: 29. marec 2022
Zamenjuje izdajo, veljavno od dne / Replaces the Annex valid as of: 18. junij 2018
Akreditacija je veljavna do preklica. Veljavnost je mogoče preveriti na spletni strani SA, www.slo-akreditacija.si.
This accreditation shall remain in force until withdrawn. Information on current status is available at the SA website, www.slo-akreditacija.si.
PRILOGA K AKREDITACIJSKI LISTINI
Annex to Accreditation Certificate
K-044
1 AKREDITIRANI ORGAN / Accredited body
Branko Zorin s.p.
Pečica 1A, 3241 Podplat
2 ZAHTEVE ZA USPOSOBLJENOST / Competence Requirements
SIST EN ISO/IEC 17020:2012, tip C / type C
3 OBSEG AKREDITACIJE / Scope of accreditation
V okviru te akreditacijske listine Slovenska akreditacija priznava akreditiranemu organu usposobljenost
za opravljanje naslednjih dejavnosti: / SA hereby recognizes the accredited body as being competent to
perform the following activities:
3.1 Skrajšan opis obsega akreditacije / Brief description of the scope
• Kontrola vodomerov (1) / Inspection of water meters (1)
Priloga k akreditacijski listini
Annex to Accreditation Certificate K-044
Velja od / Valid as of 29. marec 2022
Zamenjuje izdajo, veljavno od dne / Replaces the Annex valid as of 18. junij 2018
Akreditacija je veljavna do preklica. Veljavnost preveriti na
This accreditation shall remain in force until withdrawn.
Information on current status available at
www.slo-akreditacija.si
Branko Zorin s.p., Pečica 1A, 3241 Podplat
OB05-31 Izdaja / Revision: 8 Stran / Page: 2 / 2
3.2 Podroben opis obsega akreditacije / Detailed scope of accreditation
3.2.1 Branko Zorin s.p., Pečica 1A, 3241 Podplat
Tabela / Table 1
Tip obsega: fiksni / Type of scope: fixed
Št.
No.
Predmet kontrole
(proizvod, storitev, proces)
Item of inspection
(product, service, process)
Vrsta kontrole
Inspection type
Metode in postopki
(normativni dokumenti, interni
postopki)
Methods and procedures
(normative documents, internal
procedures)
Opombe
Notes
1. Vodomeri
- za hladno vodo,
- za toplo vodo, ki jih je skladno s
certifikatom o odobritvi tipa možno
kontrolirati s hladno vodo
- redna kontrola
- izredna kontrola
- kontrola v uporabi
Pravilnik o merilnih inštrumentih (Ur.
list RS, št. 19/16), Priloga 3 -
Vodomeri (MI 001)
Velikost vodomerov:
(DN15 - DN40) mm
Pretok:
od 15 l/h do 16 m3/h
Volumen:
(5 - 350) l
Datum / Date: 29. marec 2022 Direktor / Director
dr. Boštjan Godec
Kopija priloge k akreditacijski listini za objavo na spletnem mestu.
Podpisani original priloge na vpogled na sedežu SA.
Copy of Annex to the accreditation certificate for web publishing.
Signed original of Annex available for consultation at the SA head office.
ARRIVA d.o.o.
OB05-31 Izdaja / Revision: 7 Stran / Page: 1 / 2
Reg. št. / Ref. No.: 3150-0030/10-0014
Velja od / Valid as of: 17. december 2021
Zamenjuje izdajo, veljavno od dne / Replaces the Annex valid as of: 24. december 2020
Akreditacija je veljavna do preklica. Veljavnost je mogoče preveriti na spletni strani SA, www.slo-akreditacija.si.
This accreditation shall remain in force until withdrawn. Information on current status is available at the SA website, www.slo-akreditacija.si.
PRILOGA K AKREDITACIJSKI LISTINI
Annex to Accreditation Certificate
K-004
1 AKREDITIRANI ORGAN / Accredited body
ARRIVA d.o.o.
Ulica Mirka Vadnova 8, 4000 Kranj
2 ZAHTEVE ZA USPOSOBLJENOST / Competence Requirements
SIST EN ISO/IEC 17020:2012, tip C
3 OBSEG AKREDITACIJE / Scope of accreditation
V okviru te akreditacijske listine Slovenska akreditacija priznava akreditiranemu organu usposobljenost
za opravljanje naslednjih dejavnosti: / SA hereby recognizes the accredited body as being competent to
perform the following activities:
3.1 Skrajšan opis obsega akreditacije / Brief description of the scope
• Kontrola zapisovalne opreme v cestnem prometu (tahografi) (1, 2, 3) / Inspection of recording
equipment in road transport (tachographs) (1, 2, 3)
Priloga k akreditacijski listini
Annex to Accreditation Certificate K-004
Velja od / Valid as of 17. december 2021
Zamenjuje izdajo, veljavno od dne / Replaces the Annex valid as of 24. december 2020
Akreditacija je veljavna do preklica. Veljavnost preveriti na
This accreditation shall remain in force until withdrawn.
Information on current status available at
www.slo-akreditacija.si
DELAVNICA IN PISARNE Maribor, Meljska cesta 97, 2000 Maribor
OB05-31 Izdaja / Revision: 7 Stran / Page: 2 / 2
3.2 Podroben opis obsega akreditacije / Detailed scope of accreditation
3.2.1 DELAVNICA IN PISARNE Maribor, Meljska cesta 97, 2000 Maribor
Tabela / Table 1
Tip obsega: fiksni / Type of scope: fixed
Št.
No.
Predmet kontrole
(proizvod, storitev, proces)
Item of inspection
(product, service, process)
Vrsta kontrole
Inspection type
Metode in postopki
(normativni dokumenti, interni
postopki)
Methods and procedures
(normative documents, internal
procedures)
Opombe
Notes
1. Zapisovalna oprema v cestnem
prometu - analogni tahografi
- pred namestitvijo
- ob namestitvi
- redna
- med uporabo
Uredba (EU) št. 165/2014
Evropskega parlamenta in Sveta z
dne 4. februarja 2014 o tahografih v
cestnem prometu, Priloga I,
poglavje III(f) in VI
Pravilnik o odobritvi in nalogah
delavnic za tahografe in naprave za
omejevanje hitrosti (Ur. list RS, št.
24/19, 184/20, 163/21), čl. 5 do 16
Kontrola z metodo:
- na prostovrtečih se
valjih,
- na merilni stezi dolžine
20 m na lokaciji
kontrolnega organa
2. Zapisovalna oprema v cestnem
prometu - digitalni tahografi
- pred namestitvijo
- ob namestitvi
- redna
- med uporabo
Uredba Sveta (EGS) 3821/85 o
tahografu (nadzorni napravi) v
cestnem prometu, Priloga IB,
poglavje III, točke 2.1, 2.2 in 3 in
poglavje VI
Pravilnik o odobritvi in nalogah
delavnic za tahografe in naprave za
omejevanje hitrosti (Ur. list RS, št.
24/19, 184/20, 163/21), čl. 5 do 16
Kontrola z metodo:
- na prostovrtečih se
valjih,
- na merilni stezi dolžine
20 m na lokaciji
kontrolnega organa
3. Zapisovalna oprema v cestnem
prometu - pametni tahografi
- pred namestitvijo
- ob namestitvi
- redna
- med uporabo
Izvedbena Uredba Komisije (EU)
2016/799 z dne 18. marca 2016 o
izvajanju Uredbe (EU) št.165/2014
Evropskega parlamenta in Sveta
za določitev zahtev glede
konstrukcije, preskušanja,
namestitve, delovanja in popravila
tahografov in njihovih sestavnih
delov, Priloga IC, poglavja 3.2, 3.3
in 6.
Pravilnik o odobritvi in nalogah
delavnic za tahografe in naprave za
omejevanje hitrosti (Ur. list RS, št.
24/19, 184/20, 163/21), čl. 5 do 16
Kontrola z metodo:
- na prostovrtečih se
valjih,
- na merilni stezi dolžine
20 m na lokaciji
kontrolnega organa
Datum / Date: 21.12.2021 Direktor / Director
dr. Boštjan Godec
Kopija priloge k akreditacijski listini za objavo na spletnem mestu.
Podpisani original priloge na vpogled na sedežu SA.
Copy of Annex to the accreditation certificate for web publishing.
Signed original of Annex available for consultation at the SA head office.
Fabijan lab, laboratorijske storitve, Zvonko Fabijan, s.p.
OB05-25 Izdaja / Revision: 8 Stran / Page: 1 / 3
Reg. št. / Ref. No.: 3150-0017/17-0005
Velja od / Valid as of:: 16. avgust 2023
Zamenjuje izdajo, veljavno od dne / Replaces the Annex valid as of: 16. november 2022
Akreditacija je veljavna do preklica. Veljavnost je mogoče preveriti na spletni strani SA, www.slo-akreditacija.si.
This accreditation shall remain in force until withdrawn. Information on current status is available at the SA website, www.s lo-akreditacija.si.
PRILOGA K AKREDITACIJSKI LISTINI
Annex to Accreditation Certificate
LP-115
1 AKREDITIRANI ORGAN / Accredited body
Fabijan lab, laboratorijske storitve, Zvonko Fabijan, s.p.
Vosek 6e, 2231 Pernica
2 ZAHTEVE ZA USPOSOBLJENOST / Competence Requirements
SIST EN ISO/IEC 17025:2017
3 OBSEG AKREDITACIJE / Scope of accreditation
V okviru te akreditacijske listine Slovenska akreditacija priznava akreditiranemu organu usposobljenost
za opravljanje naslednjih dejavnosti: / SA hereby recognizes the accredited body as being competent to
perform the following activities:
3.1 Skrajšan opis obsega akreditacije / Brief description of the scope
Področja preskušanja glede na vrsto preskušanja / Testing fields with reference to the type of test:
• kemija / chemistry
Področja preskušanja glede na vrsto preskušanca / Testing fields with reference to the type of test item:
• živila in vzorci prehranske verige (vino) / foodstuffs and food chain samples (wine)
Priloga k akreditacijski listini
Annex to Accreditation Certificate LP-115
Velja od / Valid as of 16. avgust 2023
Zamenjuje izdajo, veljavno od dne / Replaces the Annex valid as of 16. november 2022
Akreditacija je veljavna do preklica. Veljavnost preveriti na
This accreditation shall remain in force until withdrawn.
Information on current status available at
www.slo-akreditacija.si
Fabijan lab, laboratorijske storitve, Zvonko Fabijan, s.p., Vosek 6e, 2231 Pernica
OB05-25 Izdaja / Revision: 8 Stran / Page: 2 / 3
3.2 Podroben opis obsega akreditacije / Detailed scope of accreditation
3.2.1 Fabijan lab, laboratorijske storitve, Zvonko Fabijan, s.p., Vosek 6e, 2231 Pernica
Tabela / Table 1
Tip obsega: fiksni / Type of scope: fixed
Mesto izvajanja: v laboratoriju / Site: in the laboratory
Področja preskušanja glede na vrsto preskušanja: kemija / Testing fields with reference to the type of test: chemistry
Področja preskušanja glede na vrsto preskušanca: živila in vzorci prehranske verige (vino) / Testing fields with reference to the type of
test item: foodstuffs and food chain samples (wine)
Št.
No.
Oznaka dokumenta,
ki opisuje metodo
preskušanja
Identification of the
document, describing the
testing method
Preskušana lastnost
oziroma parameter
Characteristic or
parameter tested
Opredelitev preskusa
(vrsta, princip oziroma
tehnika preskusa)
Description of test
(type of test, test principle or
technique)
Območje
preskušanja
Range of testing
Preskušanci
(materiali,
proizvodi)
Items tested
(materials,
products)
1. OIV-MA-AS312-01A:R2016 alkohol
alcohol
destilacija z elektronsko
denzimetrijo
destilation with electronic
densimetry
(8,50 – 16,00) %vol vino
wine
2. OIV-MA-AS2-01A:R2012 relativna gostota pri 20°C
specific gravity at 20°C
elektronska denzimetrija
electronic densimetry
0,9890 – 1,0500 vino
wine
3. OIV-MA-AS313-01:R2015 skupne kisline
total acidity
avtomatska
potenciometrična titracija do
končne točke pH = 7,0
automatic potentiometric
titration with endpoint
pH = 7.0
(3,50 – 8,50) g/l
izražene kot vinska
kislina
expressed as tartaric
acid
vino
wine
4. OIV-MA-AS313-15:R2011 pH
pH
potenciometrija
potentiometry
3,00 – 4,00 vino
wine
5. OIV-MA-AS323-04B:R2009
modificirana
modified
skupni in prosti žveplov
dioksid
total and free sulphur
dioxide
avtomatska jodometrična
titracija s potenciometrično
določitvijo konca titracije
automatic iodometric
titration with potentiometric
endpoint determination
skupni žveplov
dioksid
total sulphur dioxide
(40 – 400) mg/l
prosti žveplov dioksid
free sulphur dioxide
(10 – 80) mg/l
vino
wine
6. OIV-MA-AS311-02:R2009 reducirajoči sladkorji
(glukoza in fruktoza)
reducing sugars
(glucose and fructose)
encimatska metoda na
principu spektrofotometrične
določitve NADPH
enzymatic method, with
spectrophotometric
determination of NADPH
(1,0 – 160) g/l vino
wine
7. OIV-MA-AS311-02:R2009
modificirana
modified
saharoza, reducirajoči
sladkorji z invertazo
sucrose, reducing sugars
with invertase
hidroliza z invertazo –
encimatska metoda na
principu spektrofotometrične
določitve NADPH
hydrolysis by invertase –
enzymatic method, with
spectrophotometric
determination of NADPH
saharoza
sucrose
(0,5 – 40,0) g/l
reducirajoči sladkorji z
invertazo
reducing sugars with
invertase
(1,0 – 160) g/l
vino
wine
8. OIV-MA-AS2-03B:R2012
izračun iz: / calculated from:
OIV-MA-AS312-01A:R2016,
OIV-MA-AS2-01A:R2012,
NL02, ver. 5
skupni suhi ekstrakt
total dry matter
računsko
calculation
(15 – 100) g/l vino
wine
Priloga k akreditacijski listini
Annex to Accreditation Certificate LP-115
Velja od / Valid as of 16. avgust 2023
Zamenjuje izdajo, veljavno od dne / Replaces the Annex valid as of 16. november 2022
Akreditacija je veljavna do preklica. Veljavnost preveriti na
This accreditation shall remain in force until withdrawn.
Information on current status available at
www.slo-akreditacija.si
Fabijan lab, laboratorijske storitve, Zvonko Fabijan, s.p., Vosek 6e, 2231 Pernica
OB05-25 Izdaja / Revision: 8 Stran / Page: 3 / 3
Tip obsega: fiksni / Type of scope: fixed
Mesto izvajanja: v laboratoriju / Site: in the laboratory
Področja preskušanja glede na vrsto preskušanja: kemija / Testing fields with reference to the type of test: chemistry
Področja preskušanja glede na vrsto preskušanca: živila in vzorci prehranske verige (vino) / Testing fields with reference to the type of
test item: foodstuffs and food chain samples (wine)
Št.
No.
Oznaka dokumenta,
ki opisuje metodo
preskušanja
Identification of the
document, describing the
testing method
Preskušana lastnost
oziroma parameter
Characteristic or
parameter tested
Opredelitev preskusa
(vrsta, princip oziroma
tehnika preskusa)
Description of test
(type of test, test principle or
technique)
Območje
preskušanja
Range of testing
Preskušanci
(materiali,
proizvodi)
Items tested
(materials,
products)
9. OIV-MA-AS314-02:R2003 nadtlak
overpressure
meritev s pomočjo
afrometra z mehansko
Bourdonovo cevjo
measurement using
aphrometer with mechanical
Bourdon tube
(2,0 – 8,0) bar
peneče in biser
vino
sparkling and
semi-sparkling
wine
10. NL02, ver 5
interna metoda
in-house method
parametri kakovosti vina:
relativna gostota pri 20°C,
alkohol,
hlapne kisline,
skupne kisline,
mlečna kislina,
reducirajoči sladkorji
wine quality parameters:
specific gravity at 20°C,
alcohol,
volatile acidity,
total acidity,
lactic acid,
reducing sugars
FTIR spektroskopija
FTIR spectroscopy
relativna gostota
specific gravity
0,9890 – 1,0500
alkohol
alcohol
(8,50 – 16,00) %vol
hlapne kisline
volatile acidity
(0,10 – 1,50) g/l
izražene kot ocetna
kislina
expressed as acetic
acid
skupne kisline
total acidity
(3,50 – 8,50) g/l
izražene kot vinska
kislina
expressed as tartaric
acid
mlečna kislina
lactic acid
(0,50 – 2,00) g/l
reducirajoči sladkorji
reducing sugars
(1,50 – 200,0) g/l
vino
wine
Opombe / Notes:
• V vseh točkah podrobnega obsega akreditacije, pri katerih v rubriki "Območje preskušanja" ni navedenih podatkov, veljajo določila
posameznih standardov oziroma drugih javno dostopnih dokumentov, ki opisujejo metodo.
In all columns of the scope of accreditation where the cells under "Range of testing" are empty, the provisions of the relevant standards or
other publicly available documents describing testing methods should apply.
Datum / Date: 16. 8. 2023 Direktor / Director
Dr. Boštjan Godec Kopija priloge k akreditacijski listini za objavo na spletnem mestu.
Podpisani original priloge na vpogled na sedežu SA.
Copy of Annex to the accreditation certificate for web publishing.
Signed original of Annex available for consultation at the SA head office.
TAB d.d.
OB05-25 Izdaja / Revision: 8 Stran / Page: 1 / 6
Reg. št. / Ref. No.: 3150-0019/19-0003
Velja od / Valid as of:: 15. november 2022
Zamenjuje izdajo, veljavno od dne / Replaces the Annex valid as of:: 16. november 2021
Akreditacija je veljavna do preklica. Veljavnost je mogoče preveriti na spletni strani SA, www.slo-akreditacija.si.
This accreditation shall remain in force until withdrawn. Information on current status is available at the SA website, www.slo-akreditacija.si.
PRILOGA K AKREDITACIJSKI LISTINI
Annex to Accreditation Certificate
LP-119
1 AKREDITIRANI ORGAN / Accredited body
TAB d.d.
Polena 6, 2392 Mežica
2 ZAHTEVE ZA USPOSOBLJENOST / Competence Requirements
SIST EN ISO/IEC 17025:2017
3 OBSEG AKREDITACIJE / Scope of accreditation
V okviru te akreditacijske listine Slovenska akreditacija priznava akreditiranemu organu usposobljenost
za opravljanje naslednjih dejavnosti: / SA hereby recognizes the accredited body as being competent to
perform the following activities:
3.1 Skrajšan opis obsega akreditacije / Brief description of the scope
Področja preskušanja glede na vrsto preskušanja / Testing fields with reference to the type of test:
• Elektrotehnika, elektronika / electrotechnics, electronics
Področja preskušanja glede na vrsto preskušanca / Testing fields with reference to the type of test item:
• Elektronske naprave / electronic device
Priloga k akreditacijski listini
Annex to Accreditation Certificate LP-119
Velja od / Valid as of 15. november 2022
Zamenjuje izdajo, veljavno od dne / Replaces the Annex valid as of 16. november 2021
Akreditacija je veljavna do preklica. Veljavnost preveriti na
This accreditation shall remain in force until withdrawn.
Information on current status available at
www.slo-akreditacija.si
Elektrofizikalni laboratorij (EFL), Mušenik 18, 2393 Črna na Koroškem
OB05-25 Izdaja / Revision: 8 Stran / Page: 2 / 6
3.2 Podroben opis obsega akreditacije / Detailed scope of accreditation
3.2.1 Elektrofizikalni laboratorij (EFL), Mušenik 18, 2393 Črna na Koroškem
Tabela / Table 1
Tip obsega: fiksni / Type of scope: fixed
Mesto izvajanja: v laboratoriju / Site: in the laboratory
Področja preskušanja glede na vrsto preskušanja: elektrotehnika, elektronika / Testing fields with reference to the type of test:
electrotechnics, electronics
Področja preskušanja glede na vrsto preskušanca: elektronske naprave / Testing fields with reference to the type of test item:
electronic device
Št.
No.
Oznaka
dokumenta,
ki opisuje metodo
preskušanja
Identification of
the document,
describing the
testing method
Preskušana lastnost
oziroma parameter
Characteristic or parameter
tested
Opredelitev preskusa
(vrsta, princip oziroma tehnika preskusa)
Description of test
(type of test, test principle or technique)
Območje
preskušanja
Range of testing
Preskušanci
(materiali,
proizvodi)
Items tested
(materials,
products)
1. EN 50342-1:2015 kapaciteta, zagonska
sposobnost, sposobnost
praznjenja z visokim tokom,
sposobnost polnjenja,
ohranjanje napolnjenosti,
ciklična vzdržljivost, korozijska
obstojnost, globoko
praznjenje, poraba vode,
vibracijska odpornost,
zadrževanje elektrolita,
sposobnost hitrega praznjenja
capacity, cranking
performance, high current
discharge, charge
acceptance, charge retention,
endurance in cycle, corrosion
resistance, deep discharge,
water consumption, vibration
resistance, electrolyte
retention, rapid discharge
-(6.1) Test kapacitete baterije C20
-(6.2) Test hladnega zagona
-(6.3) Test praznjenja z visokim tokom
pri nizki temperaturi
-(6.4) Test sposobnosti polnjenja
-(6.5) Test ohranjanja napolnjenosti
-(6.6) Test ciklične vzdržljivost
-(6.7) Test korozije
-(6.8) Test globokega praznjenja
-(6.9) Test porabe vode
-(6.10) Test vibracijske odpornosti
-(6.11) Test zadrževanja elektrolita
-(7.3) Hitro praznjenje po aktivaciji
-(6.1) Capacity test C20
-(6.2) Cranking performance test
-(6.3) High current discharge test at low
temperature
-(6.4) Charge acceptance test
-(6.5) Charge retention test
-(6.6) Endurance in cycle test
-(6.7) Corrosion test
-(6.8) Deep discharge test
-(6.9) Water consumption test
-(6.10) Vibration resistance test
-(6.11) Electrolyte retention test
-(7.3) Rapid discharge test after
activation
C20:(0 - 300) Ah
Ubat: (0 - 20) V
I C20: (0 - 25) A
tC20: (0 - 20) h
IHRDT: (0 - 2000) A
tHRD: (0 - 150) s
RC:(0 - 480) min
T: (-18 - +60) °C
Svinčeno-
kislinske
zaganjalne
baterije
Lead acid
starter battery
2. EN 50342-6:2015 sposobnost zagona,
dinamična sposobnost
polnjenja, ciklična sposobnost
ability to restart, dynamic
charge acceptance,
endurance in cycle
-(7.2) Mikro-hibridni test (MHT)
-(7.3) Test dinamične sposobnosti
polnjenja (TDSP)
-(7.4) Test vzdržljivosti pri ciklanju s
17,5 % globokim praznjenjem
-(7.5) Test vzdržljivosti pri ciklanju s 50
% globokim praznjenjem in predhodnim
globokim praznjenjem
-(7.2) Micro-hybrid test (MHT)
-(7.3) Dynamic charge acceptance test
(DCA)
-(7.4) Endurance in cycle test with 17,5
% depth of discharge (DoD)
-(7.5) Endurance in cycle test with 50 %
depth of discharge (DoD) at 40 °C and
preceded deep discharge
C20:(0 - 300) Ah
Ubat: (0 - 20) V
I C20: (0 - 25) A
tC20: (0 - 20) h
IHRDT: (0 - 2000) A
tHRD: (0 - 150) s
RC:(0 - 480) min
T: (-18 - +60) °C
Svinčeno-
kislinske
zaganjalne
baterije
Lead acid
starter battery
Priloga k akreditacijski listini
Annex to Accreditation Certificate LP-119
Velja od / Valid as of 15. november 2022
Zamenjuje izdajo, veljavno od dne / Replaces the Annex valid as of 16. november 2021
Akreditacija je veljavna do preklica. Veljavnost preveriti na
This accreditation shall remain in force until withdrawn.
Information on current status available at
www.slo-akreditacija.si
Elektrofizikalni laboratorij (EFL), Mušenik 18, 2393 Črna na Koroškem
OB05-25 Izdaja / Revision: 8 Stran / Page: 3 / 6
Tip obsega: fiksni / Type of scope: fixed
Mesto izvajanja: v laboratoriju / Site: in the laboratory
Področja preskušanja glede na vrsto preskušanja: elektrotehnika, elektronika / Testing fields with reference to the type of test:
electrotechnics, electronics
Področja preskušanja glede na vrsto preskušanca: elektronske naprave / Testing fields with reference to the type of test item:
electronic device
Št.
No.
Oznaka
dokumenta,
ki opisuje metodo
preskušanja
Identification of
the document,
describing the
testing method
Preskušana lastnost
oziroma parameter
Characteristic or parameter
tested
Opredelitev preskusa
(vrsta, princip oziroma tehnika preskusa)
Description of test
(type of test, test principle or technique)
Območje
preskušanja
Range of testing
Preskušanci
(materiali,
proizvodi)
Items tested
(materials,
products)
3. GSO 35/2007
kapaciteta, sposobnost
hitrega praznjenja, zagonska
sposobnost, rezervna
kapaciteta, sposobnost
polnjenja, ohranjanje
napolnjenosti, ciklična
vzdržljivost, tesnost ohišja,
poraba vode, vibracijska
odpornost, zadrževanje
elektrolita, iztekanje
elektrolita, vzdržljivost
terminalov
capacity, rapid discharge,
cranking performance,
reserve capacity, charge
acceptance, conservation of
charge, cycling ability, air
leakage of housing, water
consumption, vibration
resistance, electrolyte
retention, leakage of
electrolyte, strength of
terminals
-(9) Test 20 h kapacitete (Počasno
praznjenje)
-(10) Test hitrega praznjenje po
aktivaciji suhopolnjene baterije pri 25 °C
-(11) Test hladnega zagona pri -18 °C
-(12) Test rezervne kapacitete (RC)
-(13) Test sposobnosti polnjenja
-(14) Test ohranjanja napolnjenosti
-(15) Test življenjske dobe, vzdržljivost
-(16) Test uhajanje zraka iz ohišja.
-(17) Test porabe vode
-(18) Test vibracijske odpornosti
-(19) Test zadrževanje elektrolita.
-(20) Preskus iztekanja elektrolita pri
različnih temperaturah
-(21) Test trdnost terminalov pri
obremenitvi določenim navorom
-(9) Checking of rated capacity “C20”
(slow discharge rate capacity)
-(10) Rapid discharge capacity test of a
dry charged battery at normal
temperature (activation test)
-(11) Rapid discharge capacity test at
low temperature
-(12) Reserve Capacity test (RC)
-(13) Charge acceptance test
-(14) Conservation of charge test
-(15) Battery life test (endurance test)
-(16) Air Leakage of the housing.
-(17) Water consumption test
-(18) Vibration resistance test
-(19) Electrolyte retention test
-(20) Test for leakage of electrolyte at
different temperatures
-(21) Test for strength of terminal
C20:(0 - 300) Ah
Ubat: (0 - 20) V
I C20: (0 - 25) A
tC20: (0 - 20) h
IHRDT: (0 - 2000) A
tHRD: (0 - 150) s
RC:(0 - 480) min
T: (-18 - +60) °C
Navor: (0 - 15)
Nm
Svinčeno-
kislinske
zaganjalne
baterije
Lead acid
starter battery
4. IEC 60254-1:2005
EN 60254-1:2005
kapaciteta, ohranjanje
napolnjenosti, sposobnost
praznjenja z velikim tokom,
ciklična sposobnost
capacity, charge retention,
high-rate discharge, cyclic
endurance
-(5.2) Kapacitetni test
-(5.3) Test ohranjanja napolnjenosti
-(5.4) Test praznjenja z velikim tokom
-(5.5) Test ciklične sposobnosti
-(5.2) Capacity test
-(5.3) Charge retention test
-(5.4) High-rate discharge performance
test
-(5.5) Cyclic Endurance test
C5:(0 – 200) Ah
U: (0 - 20) V
I: (0 - 300) A
Žvepleno-
kislinske
vlečne
baterije
Lead - acid
traction
batteries
Priloga k akreditacijski listini
Annex to Accreditation Certificate LP-119
Velja od / Valid as of 15. november 2022
Zamenjuje izdajo, veljavno od dne / Replaces the Annex valid as of 16. november 2021
Akreditacija je veljavna do preklica. Veljavnost preveriti na
This accreditation shall remain in force until withdrawn.
Information on current status available at
www.slo-akreditacija.si
Elektrofizikalni laboratorij (EFL), Mušenik 18, 2393 Črna na Koroškem
OB05-25 Izdaja / Revision: 8 Stran / Page: 4 / 6
Tip obsega: fiksni / Type of scope: fixed
Mesto izvajanja: v laboratoriju / Site: in the laboratory
Področja preskušanja glede na vrsto preskušanja: elektrotehnika, elektronika / Testing fields with reference to the type of test:
electrotechnics, electronics
Področja preskušanja glede na vrsto preskušanca: elektronske naprave / Testing fields with reference to the type of test item:
electronic device
Št.
No.
Oznaka
dokumenta,
ki opisuje metodo
preskušanja
Identification of
the document,
describing the
testing method
Preskušana lastnost
oziroma parameter
Characteristic or parameter
tested
Opredelitev preskusa
(vrsta, princip oziroma tehnika preskusa)
Description of test
(type of test, test principle or technique)
Območje
preskušanja
Range of testing
Preskušanci
(materiali,
proizvodi)
Items tested
(materials,
products)
5. IEC 60095-1:2018 kapaciteta, rezervna
kapaciteta, zagonska
sposobnost, sposobnost
polnjenja, ohranjanje
napolnjenosti, korozijska
obstojnost, ciklična
vzdržljivost, poraba vode,
vibracijska odpornost,
zadrževanje elektrolita,
sposobnost zagona
capacity, reserve capacity,
cranking performance, charge
acceptance, charge retention,
corrosion resistance, cycling
ability, water consumption,
vibration resistance,
electrolyte retention, cranking
performance
-(9.1) Kapacitetni test baterije C20
-(9.2) Test rezervne kapacitete
-(9.3) Test praznjenja z zagonskim
tokom Icc, ki ga baterija zagotavlja pri
nizki temperaturi
-(9.4) Test sposobnosti polnjenja pri 0°C
-(9.5) Test ohranjanja napolnjenosti
-(9.6.1) Test korozijske obstojnosti
-(9.6.1.2) Test ciklične vzdržljivosti
-(9.7) Test porabe vode
-(9.8) Test vibracijske odpornosti
-(9.9) Preskus iztekanja elektrolita pri
različnih temperaturah
-(9.10) Test sposobnosti zagona suhih
baterij po aktivaciji
-(9.1) Capacity test C20
-(9.2) Reserve capacity check
-(9.3) Discharge with cranking current
Icc which battery can supply at low
temperature
-(9.4) Charge acceptance test at 0°C
-(9.5) Charge retention test
-(9.6.1) Corrosion test
-(9.6.1.2) Endurance in cycle test
-(9.7) Water consumption test
-(9.8) Vibration resistance test
-(9.9) Electrolyte retention test
-(9.10) Cranking performance for dry-
charged batteries after activation
C20:(0 - 300) Ah
Ubat: (0 - 20) V
I C20: (0 - 25) A
tC20: (0 - 20) h
IHRDT: (0 - 2000) A
tHRD: (0 - 150) s
RC:(0 - 480) min
T: (-18 - +60) °C
Svinčeno-
kislinske
zaganjalne
baterije
Lead acid
starter battery
Priloga k akreditacijski listini
Annex to Accreditation Certificate LP-119
Velja od / Valid as of 15. november 2022
Zamenjuje izdajo, veljavno od dne / Replaces the Annex valid as of 16. november 2021
Akreditacija je veljavna do preklica. Veljavnost preveriti na
This accreditation shall remain in force until withdrawn.
Information on current status available at
www.slo-akreditacija.si
Razvojno-raziskovalni laboratorij RRL, Žerjav 81, 2393 Črna na Koroškem
OB05-25 Izdaja / Revision: 8 Stran / Page: 5 / 6
3.2.2 Razvojno-raziskovalni laboratorij RRL, Žerjav 81, 2393 Črna na Koroškem
Tabela / Table 2
Tip obsega: fiksni / Type of scope: fixed
Mesto izvajanja: v laboratoriju / Site: in the laboratory
Področja preskušanja glede na vrsto preskušanja: elektrotehnika, elektronika / Testing fields with reference to the type of test:
electrotechnics, electronics
Področja preskušanja glede na vrsto preskušanca: elektronske naprave / Testing fields with reference to the type of test item: electronic
device
Št.
No.
Oznaka dokumenta,
ki opisuje metodo
preskušanja
Identification of the
document, describing the
testing method
Preskušana lastnost /
parameter
Characteristic /
parameter tested
Opredelitev preskusa
(vrsta, princip oziroma tehnika
preskusa)
Description of test
(type of test, test principle or
technique)
Območje
preskušanja
Range of testing
Preskušanci
(materiali,
proizvodi)
Items tested
(materials,
products)
6. IEC 60896-11:2002
EN 60896-11:2003
kapaciteta, sposobnost
vzdrževanja polnilne
napetosti, ciklična
sposobnost, vzdržljivost
na
prepolnjevanje,
ohranjanje
napolnjenosti,
kratkostični tok in
notranja upornost
capacity, suitability for
floating battery
operation, endurance in
discharge-charge
cycles, endurance in
overcharge, charge
retention, short circuit
current and Internal
resistance
-(7) Kapacitetni test
-(8) Test sposobnosti vzdrževanja
polnilne napetosti
-(9.1) Test ciklične sposobnosti
-(9.2) Test vzdržljivosti na
prepolnjevanje
-(10) Test ohranjanja napolnjenosti
-(11) Določitev kratkostičnega toka in
notranje upornosti
-(7) Capacity test
-(8) Test of suitability for floating
battery operation
-(9.1) Endurance in discharge-charge
cycles
-(9.2) Endurance in overcharge
-(10) Charge retention test
-(11) Short circuit current and
internal resistance determination
C10:(0 - 3500) Ah
U: (0 - 20) V
I: (0 - 2000) A
Stacionarne
svinčeno-
kislinske baterije
(standardni,
odprti tipi)
Stationary lead-
acid batteries
(vented types)
7. IEC 60896-21:2004,
EN 60896-21:2004
Brez točk / Without
following points:
6.1,6.2,6.4,6.5,6.6,
6.7,6.8,6.9,6.10,6.15,
6.16, 6.18,6.19,6.20,6.21
kratkostični tok in
notranja upornost,
kapaciteta, ohranjanje
napolnjenosti,
sposobnost vzdrževanja
polnilne napetosti,
obnašanje pri polnjenju,
vpliv prekomernega
praznjenja
short circuit current and
Internal resistance,
capacity, charge
retention, suitability for
floating battery
operation, recharge
behaviour, abusive
over-discharge
performance
-(6.3) Določitev kratkostičnega toka in
notranje upornosti
-(6.11) Kapacitetni test
-(6.12) Test ohranjanja napolnjenosti
-(6.13) Test sposobnosti vzdrževanja
napetosti
-(6.14) Test obnašanja pri polnjenju
-(6.17) Test prekomernega praznjenja
-(6.3) Short circuit current and
internal resistance determination
-(6.11) Discharge capacity test
-(6.12) Charge retention during
storage test
-(6.13) Float service with daily
discharges test
-(6.14) Recharge behaviour test
-(6.17) Abusive over-discharge test
C10: (0 - 3500) Ah
U: (0 - 20) V
I: (0 - 2000) A
Stacionarne
svinčeno-
kislinske baterije
(ventilsko-
regulirani tipi)
Stationary lead-
acid batteries
(valve regulated
types)
8. IEC 60254-1:2005
EN 60254-1:2005
kapaciteta, ohranjanje
napolnjenosti,
sposobnost praznjenja z
velikim tokom, ciklična
sposobnost
capacity, charge
retention, high-rate
discharge, cyclic
endurance
-(5.2) Kapacitetni test
-(5.3) Test ohranjanja napolnjenosti
-(5.4) Test praznjenja z velikim tokom
-(5.5) Test ciklične sposobnosti
-(5.2) Capacity test
-(5.3) Charge retention test
-(5.4) High-rate discharge
performance test
-(5.5) Cyclic Endurance test
C5:(0 - 2200) Ah
U: (0 - 20) V
I: (0 - 2000) A
Žvepleno-
kislinske vlečne
baterije
Lead- acid
traction batteries
Priloga k akreditacijski listini
Annex to Accreditation Certificate LP-119
Velja od / Valid as of 15. november 2022
Zamenjuje izdajo, veljavno od dne / Replaces the Annex valid as of 16. november 2021
Akreditacija je veljavna do preklica. Veljavnost preveriti na
This accreditation shall remain in force until withdrawn.
Information on current status available at
www.slo-akreditacija.si
Razvojno-raziskovalni laboratorij RRL, Žerjav 81, 2393 Črna na Koroškem
OB05-25 Izdaja / Revision: 8 Stran / Page: 6 / 6
Opombe / Notes:
• V vseh točkah podrobnega obsega akreditacije, pri katerih v rubriki "Območje preskušanja" ni navedenih podatkov, veljajo določila
posameznih standardov oziroma drugih javno dostopnih dokumentov, ki opisujejo metodo.
In all columns of the scope of accreditation where the cells under "Range of testing" are empty, the provisions of the relevant standards or
other publicly available documents describing testing methods should apply.
Datum / Date: 15.11.2022 Direktor / Director
Dr. Boštjan Godec
Kopija priloge k akreditacijski listini za objavo na spletnem mestu.
Podpisani original priloge na vpogled na sedežu SA.
Copy of Annex to the accreditation certificate for web publishing.
Signed original of Annex available for consultation at the SA head office.
IRMA d.o.o.
OB05-25 Izdaja / Revision: 8 Stran / Page: 1 / 10
Reg. št. / Ref. No.: 3150-0017/10-0019
Velja od / Valid as of: 7. september 2023
Zamenjuje izdajo, veljavno od dne / Replaces the Annex valid as of: 8. november 2022
Akreditacija je veljavna do preklica. Veljavnost je mogoče preveriti na spletni strani SA, www.slo-akreditacija.si.
This accreditation shall remain in force until withdrawn. Information on current status is available at the SA website, www.slo-akreditacija.si.
PRILOGA K AKREDITACIJSKI LISTINI
Annex to Accreditation Certificate
LP-008
1 AKREDITIRANI ORGAN / Accredited body
IRMA d.o.o.
Špruha 18, 1236 Trzin
2 ZAHTEVE ZA USPOSOBLJENOST / Competence Requirements
SIST EN ISO/IEC 17025:2017
3 OBSEG AKREDITACIJE / Scope of accreditation
V okviru te akreditacijske listine Slovenska akreditacija priznava akreditiranemu organu usposobljenost
za opravljanje naslednjih dejavnosti: / SA hereby recognizes the accredited body as being competent to
perform the following activities:
3.1 Skrajšan opis obsega akreditacije / Brief description of the scope
Področja preskušanja glede na vrsto preskušanja / Testing fields with reference to the type of test:
• mehansko preskušanje / mechanical testing
• fizikalno preskušanje / physical testing
• vzorčenje / sampling
Področja preskušanja glede na vrsto preskušanca / Testing fields with reference to the type of test item:
• gradbeni proizvodi, materiali in konstrukcije (beton, malta, opeka, gradbeni proizvodi, kamen in
agregati) / construction products, materials and structures (concrete, mortar, brick, construction
products, stone and aggregates)
Priloga k akreditacijski listini
Annex to Accreditation Certificate LP-008
Velja od / Valid as of 7. september 2023
Zamenjuje izdajo, veljavno od dne / Replaces the Annex valid as of 8. november 2022
Akreditacija je veljavna do preklica. Veljavnost preveriti na
This accreditation shall remain in force until withdrawn.
Information on current status available at
www.slo-akreditacija.si
Preskusni laboratorij, Špruha 18, 1236 Trzin
OB05-25 Izdaja / Revision: 8 Stran / Page: 2 / 10
3.2 Podroben opis obsega akreditacije / Detailed scope of accreditation
3.2.1 Preskusni laboratorij, Špruha 18, 1236 Trzin
Tabela / Table 1
Tip obsega: fleksibilni (možnost uvajanja manjših sprememb metode)* / Type of scope: flexible (possibility of introducing minor
modifications to the method)*
Mesto izvajanja: v laboratoriju ali na terenu / Site: in the laboratory or fieldwork
Področja preskušanja glede na vrsto preskušanja: mehansko preskušanje; fizikalno preskušanje; vzorčenje / Testing fields with
reference to the type of test: mechanical testing; physical testing; sampling
Področja preskušanja glede na vrsto preskušanca: gradbeni proizvodi, materiali in konstrukcije (beton) / Testing fields with reference
to the type of test item: construction products, materials and structures (concrete)
Št.
No.
Oznaka dokumenta,
ki opisuje metodo
preskušanja
Identification of the
document, describing the
testing method
Preskušana lastnost /
parameter
Characteristic / parameter
tested
Opredelitev preskusa
(vrsta, princip oziroma
tehnika preskusa)
Description of test
(type of test, test principle or
technique)
Območje
preskušanja
Range of testing
Preskušanci
(materiali,
proizvodi)
Items tested
(materials,
products)
1. SIST EN 12350-1 Vzorčenje za fizikalne in
mehanske preiskave
Sampling for physical and
mechanical testing
Ročni odvzem
posameznega in/ali
zbirnega vzorca
Manual sampling of spot
and/or composite sample
sveži beton
fresh concrete
2. SIST EN 12350-2 Konsistenca
Consistency
Posed stožca
Slump-test
sveži beton
fresh concrete
3. SIST EN 12350-5 Konsistenca
Consistency
Razlez na stresalni mizi
Flow table test
sveži beton
fresh concrete
4. SIST EN 12350-6 Gostota
Density
Tehtanje znanega volumna
zgoščenega svežega
betona
Weighing of known volume
of compacted fresh
concrete
sveži beton
fresh concrete
5. SIST EN 12350-7
točka 6
point 6
Vsebnost zraka
Air content
Meritev zmanjšanja pritiska
v posodi z znanim
volumnom (porozimetru)
napolnjeni s svežim
betonom pod pritiskom
Measurement of pressure
reduction in air tight
container filled with
compressed fresh conrete
sveži beton
fresh concrete
Priloga k akreditacijski listini
Annex to Accreditation Certificate LP-008
Velja od / Valid as of 7. september 2023
Zamenjuje izdajo, veljavno od dne / Replaces the Annex valid as of 8. november 2022
Akreditacija je veljavna do preklica. Veljavnost preveriti na
This accreditation shall remain in force until withdrawn.
Information on current status available at
www.slo-akreditacija.si
Preskusni laboratorij, Špruha 18, 1236 Trzin
OB05-25 Izdaja / Revision: 8 Stran / Page: 3 / 10
Tip obsega: fleksibilni (možnost uvajanja manjših sprememb metode)* / Type of scope: flexible (possibility of introducing minor
modifications to the method)*
Mesto izvajanja: v laboratoriju ali na terenu / Site: in the laboratory or fieldwork
Področja preskušanja glede na vrsto preskušanja: mehansko preskušanje; fizikalno preskušanje; vzorčenje / Testing fields with
reference to the type of test: mechanical testing; physical testing; sampling
Področja preskušanja glede na vrsto preskušanca: gradbeni proizvodi, materiali in konstrukcije (beton) / Testing fields with reference
to the type of test item: construction products, materials and structures (concrete)
Št.
No.
Oznaka dokumenta,
ki opisuje metodo
preskušanja
Identification of the
document, describing the
testing method
Preskušana lastnost /
parameter
Characteristic / parameter
tested
Opredelitev preskusa
(vrsta, princip oziroma
tehnika preskusa)
Description of test
(type of test, test principle or
technique)
Območje
preskušanja
Range of testing
Preskušanci
(materiali,
proizvodi)
Items tested
(materials,
products)
6. SIST 1026
dodatek NC, ND, NE, NF
annex NC, ND, NE, NF
Vodocementno razmerje
svežega betona
Water - cement ratio of
fresh concrete
Notranja odpornost proti
zmrzovanju-tajanju -
relativni elastični modul
Internal freeze-thaw
resistance - relative
elasticity modulus
Odpornost površine proti
zmrzovanju - tajanju
Freeze - thaw surface
resistance
Odpornost proti obrabi
Wear resistance
Sušenje vzorca in tehtanje
Sample drying and weighing
Ciklično zamrzovanje in
tajanje mokrih nasičenih
preskušancev v
temperaturni komori,
meritev osnovne
transverzalne frekvence
Cyclic freezing and thawing
of samples in temperature
chamber, fundamental
transversal frequency
measurement
Ciklično zamrzovanje in
tajanje preskušancev v
temperaturni komori v
prisotnosti slanice (3 ut. %
razt. NaCl), tehtanje
odluščenega materiala
Cyclic freezing and thawing
of samples in temperature
chamber in the presence of
brine (3 wt. % NaCl),
weighing of peeld material
Brušenje preskušanca z
brusnim prahom na
rotirajoči plošči - preskus po
Böhmeju
Grinding of sample with
abrasive powder on rotating
plate - Böhme test
sveži in strjeni
beton
fresh and
hardened
concrete
7. SIST EN 445
brez točke 4.4
except point 4.4
Pretočnost
Fluidity
Sprememba volumna in
izločanje vode
Volume change and
bleeding
Tlačna trdnost
Compressive strength
Merjenje pretoka skozi
stožčast lijak
Measurement of flow - Cone
method
Merjenje razleza mase
Measurement of grout
spread
Meritev višine vode izločene
na površini mase v cevi -
Wickov preskus
Measurement of height of
bleed water - Wick-induced
test
Tlačna obremenitev
preskušancev do porušitve
Compressive loading of
specimens to failure
injekcijske malte
injection mortars
Priloga k akreditacijski listini
Annex to Accreditation Certificate LP-008
Velja od / Valid as of 7. september 2023
Zamenjuje izdajo, veljavno od dne / Replaces the Annex valid as of 8. november 2022
Akreditacija je veljavna do preklica. Veljavnost preveriti na
This accreditation shall remain in force until withdrawn.
Information on current status available at
www.slo-akreditacija.si
Preskusni laboratorij, Špruha 18, 1236 Trzin
OB05-25 Izdaja / Revision: 8 Stran / Page: 4 / 10
Tip obsega: fleksibilni (možnost uvajanja manjših sprememb metode)* / Type of scope: flexible (possibility of introducing minor
modifications to the method)*
Mesto izvajanja: v laboratoriju ali na terenu / Site: in the laboratory or fieldwork
Področja preskušanja glede na vrsto preskušanja: mehansko preskušanje; fizikalno preskušanje; vzorčenje / Testing fields with
reference to the type of test: mechanical testing; physical testing; sampling
Področja preskušanja glede na vrsto preskušanca: gradbeni proizvodi, materiali in konstrukcije (beton) / Testing fields with reference
to the type of test item: construction products, materials and structures (concrete)
Št.
No.
Oznaka dokumenta,
ki opisuje metodo
preskušanja
Identification of the
document, describing the
testing method
Preskušana lastnost /
parameter
Characteristic / parameter
tested
Opredelitev preskusa
(vrsta, princip oziroma
tehnika preskusa)
Description of test
(type of test, test principle or
technique)
Območje
preskušanja
Range of testing
Preskušanci
(materiali,
proizvodi)
Items tested
(materials,
products)
8. SIST EN 14488-1 Vzorčenje za fizikalne in
mehanske preiskave
Sampling for physical and
mechanical testing
Ročni odvzem zbirnega
vzorca sveže mešanice
Ročni odvzem
posameznega vzorca po
brizganju
Ročni odvzem
posameznega vzorca po
brizganju na betonski panel
Vrtanje jeder ali žaganje
strjenega brizganega
betona
Manual sampling of
composite sample from
fresh mix
Manual sampling of
individual sample after
spraying
Manual sampling of
individual sample after
spraying on concrete panel
Coring or sawing of
haredened sprayed
concrete
brizgani beton
sprayed concrete
9. SIST EN 14488-2 Tlačna trdnost mladega
brizganega betona
Compressive strength of
young sprayed concrete
Merjenje sile pri zabijanju
penetracijske igle do
globine 15 m ± 2 mm
Merjenje sile pri puljenju
žebljev zabitih v brizgani
beton s konstantno silo do
minimalne globine 20 mm
Measurement of force
required to push a
penetration needle to a
depth of 15 m ± 2 mm
Measurement of pull-out
force of stud driven into the
sprayed concrete at
constant force to the min.
depth of 20 mm
brizgani beton
sprayed concrete
10. SIST EN 13892-1 Vzorčenje, priprava in nega
vzorcev za fizikalne in
mehanske preiskave
Sampling, making and
curing of samples for
physical and mechanical
testing
Ročni odvzem posameznih
in kompozitnih vzorcev
Manual sampling of
individual and composite
samples
estrih
screed
11. SIST EN 13892-8 Sprijemna trdnost
Bond strength
Natezna obremenitev
preskušancev do loma
Flexural load of specimens
to failure (Pull-off test)
estrih
screed
Priloga k akreditacijski listini
Annex to Accreditation Certificate LP-008
Velja od / Valid as of 7. september 2023
Zamenjuje izdajo, veljavno od dne / Replaces the Annex valid as of 8. november 2022
Akreditacija je veljavna do preklica. Veljavnost preveriti na
This accreditation shall remain in force until withdrawn.
Information on current status available at
www.slo-akreditacija.si
Preskusni laboratorij, Špruha 18, 1236 Trzin
OB05-25 Izdaja / Revision: 8 Stran / Page: 5 / 10
12. SIST EN 12504-1 Vzorčenje
Sampling
Poškodbe
Abnormalities
Tlačna trdnost
Compressive strenght
Vrtanje jeder
Coring
Vizuelni pregled
Visual examination
Tlačna obremenitev
preskušancev do porušitve
Compressive loading of
specimens to failure
vgrajeni beton
built-in concrete
*Laboratorij lahko po potrebi uvede manjše spremembe metod (npr. prilagoditev novi izdaji). Podatke o trenutnem stanju obsega vzdržuje
laboratorij in jih objavlja. / When necessary, the laboratory may introduce minor modifications to the methods (e.g. adaptation to a new version).
Data on the current status of the scope are maintained and published by the laboratory.
Tabela / Table 2
Tip obsega: fiksni / Type of scope: fixed
Mesto izvajanja: v laboratoriju / Site: in the laboratory
Področja preskušanja glede na vrsto preskušanja: mehansko preskušanje; fizikalno preskušanje / Testing fields with reference to the
type of test: mechanical testing; physical testing
Področja preskušanja glede na vrsto preskušanca: gradbeni proizvodi, materiali in konstrukcije (beton) / Testing fields with reference
to the type of test item: construction products, materials and structures (concrete)
Št.
No.
Oznaka dokumenta,
ki opisuje metodo
preskušanja
Identification of the
document, describing the
testing method
Preskušana lastnost
oziroma parameter
Characteristic or
parameter tested
Opredelitev preskusa
(vrsta, princip oziroma
tehnika preskusa)
Description of test
(type of test, test principle or
technique)
Območje
preskušanja
Range of testing
Preskušanci
(materiali,
proizvodi)
Items tested
(materials,
products)
13. DIN 1048-5:1991
razveljavljen / withdrawn
točka 7.5
point 7.5
Statični modul elastičnosti
Static elastic modulus
Merjenje deformacije
preskušancev pri različnih
tlačnih obremenitvah
Measurement of starins at
different compressive
loadings
strjeni
beton
hardened
concrete
14. DIN 1048-2: 1991
razveljavljen / withdrawn
razen točke 5
except point 5
Vzorčenje in natezna
trdnost
Sampling and tensile
strength
Izbira in priprava cilindričnih
merskih mest z vrtanjem
Selection and slitting of test
locations
Natezna obremenitev
preskušancev do loma
Flexural load of specimens
to failure
vgrajeni beton
built-in concrete
Tabela / Table 3
Tip obsega: fleksibilni (možnost uvajanja manjših sprememb metode)* / Type of scope: flexible (possibility of introducing minor
modifications to the method)*
Mesto izvajanja: v laboratoriju / Site: in the laboratory
Področja preskušanja glede na vrsto preskušanja: mehansko preskušanje; fizikalno preskušanje / Testing fields with reference to the
type of test: mechanical testing; physical testing
Področja preskušanja glede na vrsto preskušanca: gradbeni proizvodi, materiali in konstrukcije (beton) / Testing fields with reference
to the type of test item: construction products, materials and structures (concrete)
Št.
No.
Oznaka dokumenta,
ki opisuje metodo
preskušanja
Identification of the
document, describing the
testing method
Preskušana lastnost
oziroma parameter
Characteristic or
parameter tested
Opredelitev preskusa
(vrsta, princip oziroma
tehnika preskusa)
Description of test
(type of test, test principle or
technique)
Območje
preskušanja
Range of testing
Preskušanci
(materiali,
proizvodi)
Items tested
(materials,
products)
15. ASTM C 1138M Odpornost betona na
površinsko obrabo
Surface resistance of
concrete to abrasion
Abrazija površine z
jeklenimi kroglami pod vodo
Underwater surface
abrasion with steel balls
strjeni
beton
hardened
concrete
16. SIST EN 12390-3 Tlačna trdnost
Compressive strength
Tlačna obremenitev
preskušancev do porušitve
Compressive loading of
specimens to failure
strjeni
beton
hardened
concrete
Priloga k akreditacijski listini
Annex to Accreditation Certificate LP-008
Velja od / Valid as of 7. september 2023
Zamenjuje izdajo, veljavno od dne / Replaces the Annex valid as of 8. november 2022
Akreditacija je veljavna do preklica. Veljavnost preveriti na
This accreditation shall remain in force until withdrawn.
Information on current status available at
www.slo-akreditacija.si
Preskusni laboratorij, Špruha 18, 1236 Trzin
OB05-25 Izdaja / Revision: 8 Stran / Page: 6 / 10
Tip obsega: fleksibilni (možnost uvajanja manjših sprememb metode)* / Type of scope: flexible (possibility of introducing minor
modifications to the method)*
Mesto izvajanja: v laboratoriju / Site: in the laboratory
Področja preskušanja glede na vrsto preskušanja: mehansko preskušanje; fizikalno preskušanje / Testing fields with reference to the
type of test: mechanical testing; physical testing
Področja preskušanja glede na vrsto preskušanca: gradbeni proizvodi, materiali in konstrukcije (beton) / Testing fields with reference
to the type of test item: construction products, materials and structures (concrete)
Št.
No.
Oznaka dokumenta,
ki opisuje metodo
preskušanja
Identification of the
document, describing the
testing method
Preskušana lastnost
oziroma parameter
Characteristic or
parameter tested
Opredelitev preskusa
(vrsta, princip oziroma
tehnika preskusa)
Description of test
(type of test, test principle or
technique)
Območje
preskušanja
Range of testing
Preskušanci
(materiali,
proizvodi)
Items tested
(materials,
products)
17. SIST EN 12390-5 Upogibna trdnost
Flexural strength
Upogibna obremenitev
preskušancev (vpetih v treh
točkah) do porušitve
Bending of specimens by
the application of load
trough upper and lower
rollers to failure
strjeni
beton
hardened
concrete
18. SIST EN 12390-6
samo dodatek A
only annex A
Natezna cepilna trdnost
Tensile splitting strength
Linijska tlačna obremenitev
kubičnih preskušancev do
porušitve
Narrow region compressive
loading of cubic specimens
to failure
strjeni
beton
hardened
concrete
19. SIST EN 12390-7
razen točk 6.5.1, 6.5.2, 6.5.3,
6.5.4
except points 6.5.1, 6.5.2,
6.5.3, 6.5.4
Gostota
Density
Tehtanje in določitev
volumna z izmero dimenzij
preskušancev
Weighing and volume
determination by direct
measurements of specimen
dimensions
strjeni
beton
hardened
concrete
20. SIST EN 12390-8 Globina vpijanja vode
Depth of penetration of
water
Vpijanje vode pod pritiskom,
cepitev preskušanca in
meritev globine penetracije
Water penetration under
pressure, slitting of sample,
penetration depth
measurement
strjeni
beton
hardened
concrete
21. SIST EN 1542 Sprijemna trdnost
Bond strength
Natezna obremenitev
preskušancev do loma
Flexural load of specimens
to failure (Pull-off test)
materiali za
zaščito in
sanacijo
betonskih
konstrukcij
products for the
protection and
repair of
concrete
structures
22. SIST EN 13057 Odpornost na kapilarno
absorpcijo vode
Resistance of capillary
absorption
Tehtanje vzorcev po
določenem času namakanja
v vodi
Weighing of specimens
after immersion in water for
defined time
materiali za
zaščito in
sanacijo
betonskih
konstrukcij
products for the
protection and
repair of
concrete
structures
*Laboratorij lahko po potrebi uvede manjše spremembe metod (npr. prilagoditev novi izdaji). Podatke o trenutnem stanju obsega vzdržuje
laboratorij in jih objavlja. / When necessary, the laboratory may introduce minor modifications to the methods (e.g. adaptation to a new version).
Data on the current status of the scope are maintained and published by the laboratory.
Priloga k akreditacijski listini
Annex to Accreditation Certificate LP-008
Velja od / Valid as of 7. september 2023
Zamenjuje izdajo, veljavno od dne / Replaces the Annex valid as of 8. november 2022
Akreditacija je veljavna do preklica. Veljavnost preveriti na
This accreditation shall remain in force until withdrawn.
Information on current status available at
www.slo-akreditacija.si
Preskusni laboratorij, Špruha 18, 1236 Trzin
OB05-25 Izdaja / Revision: 8 Stran / Page: 7 / 10
Tabela / Table 4
Tip obsega: fleksibilni (možnost uvajanja manjših sprememb metode)* / Type of scope: flexible (possibility of introducing minor
modifications to the method)*
Mesto izvajanja: v laboratoriju / Site: in the laboratory
Področja preskušanja glede na vrsto preskušanja: mehansko preskušanje; fizikalno preskušanje / Testing fields with reference to the
type of test:/ mechanical testing; physical testing
Področja preskušanja glede na vrsto preskušanca: gradbeni proizvodi, materiali in konstrukcije (opeka in keramika, gradbeni
proizvodi) / Testing fields with reference to the type of test item: construction products, materials and structures (brick and ceramics,
construction products)
Št.
No.
Oznaka dokumenta,
ki opisuje metodo
preskušanja
Identification of the
document, describing the
testing method
Preskušana lastnost
oziroma parameter
Characteristic or
parameter tested
Opredelitev preskusa
(vrsta, princip oziroma
tehnika preskusa)
Description of test
(type of test, test principle or
technique)
Območje
preskušanja
Range of testing
Preskušanci
(materiali,
proizvodi)
Items tested
(materials,
products)
23. SIST EN 772-1 Tlačna trdnost
Compressive strength
Tlačna obremenitev
preskušancev do porušitve
Compressive loading of
specimens to failure
opečni, apneno
peščeni in
betonski zidaki
fire-baked, lime-
sand and
concrete bricks
24. SIST EN 772-16 Dimezije
Dimensions
Direktna meritev dimenzij
Direct measurement of
dimensions
opečni, apneno
peščeni in
betonski zidaki
fire-baked, lime-
sand and
concrete bricks
*Laboratorij lahko po potrebi uvede manjše spremembe metod (npr. prilagoditev novi izdaji). Podatke o trenutnem stanju obsega vzdržuje
laboratorij in jih objavlja. / When necessary, the laboratory may introduce minor modifications to the methods (e.g. adaptation to a new version).
Data on the current status of the scope are maintained and published by the laboratory.
Priloga k akreditacijski listini
Annex to Accreditation Certificate LP-008
Velja od / Valid as of 7. september 2023
Zamenjuje izdajo, veljavno od dne / Replaces the Annex valid as of 8. november 2022
Akreditacija je veljavna do preklica. Veljavnost preveriti na
This accreditation shall remain in force until withdrawn.
Information on current status available at
www.slo-akreditacija.si
Preskusni laboratorij, Špruha 18, 1236 Trzin
OB05-25 Izdaja / Revision: 8 Stran / Page: 8 / 10
Tabela / Table 5
Tip obsega: fleksibilni (možnost uvajanja manjših sprememb metode)* / Type of scope: flexible (possibility of introducing minor
modifications to the method)*
Mesto izvajanja: v laboratoriju / Site: in the laboratory
Področja preskušanja glede na vrsto preskušanja: mehansko preskušanje; fizikalno preskušanje / Testing fields with reference to the
type of test:/ mechanical testing; physical testing
Področja preskušanja glede na vrsto preskušanca: gradbeni proizvodi, materiali in konstrukcije (cementi in malte) / Testing fields with
reference to the type of test item: construction products, materials and structures (cements and mortars)
Št.
No.
Oznaka dokumenta,
ki opisuje metodo
preskušanja
Identification of the
document, describing the
testing method
Preskušana lastnost
oziroma parameter
Characteristic or
parameter tested
Opredelitev preskusa
(vrsta, princip oziroma
tehnika preskusa)
Description of test
(type of test, test principle or
technique)
Območje
preskušanja
Range of testing
Preskušanci
(materiali,
proizvodi)
Items tested
(materials,
products)
25. SIST EN 13892-2 Upogibna in tlačna trdnost
Flexural and compressive
strength
Upogibna in tlačna
obremenitev preskušancev
do porušitve
Bending and compressive
loading of specimens to
failure
estrih
screed
26. SIST EN 13892-3 Odpornost proti obrabi
Wear resistance
Brušenje preskušanca z
brusnim prahom na
rotirajoči plošči - preskus po
Böhmeju
Grinding of sample with
abrasive powder on rotating
plate - Böhme test
estrih
screed
*Laboratorij lahko po potrebi uvede manjše spremembe metod (npr. prilagoditev novi izdaji). Podatke o trenutnem stanju obsega vzdržuje
laboratorij in jih objavlja. / When necessary, the laboratory may introduce minor modifications to the methods (e.g. adaptation to a new version).
Data on the current status of the scope are maintained and published by the laboratory.
Priloga k akreditacijski listini
Annex to Accreditation Certificate LP-008
Velja od / Valid as of 7. september 2023
Zamenjuje izdajo, veljavno od dne / Replaces the Annex valid as of 8. november 2022
Akreditacija je veljavna do preklica. Veljavnost preveriti na
This accreditation shall remain in force until withdrawn.
Information on current status available at
www.slo-akreditacija.si
Preskusni laboratorij, Špruha 18, 1236 Trzin
OB05-25 Izdaja / Revision: 8 Stran / Page: 9 / 10
Tabela / Table 6
Tip obsega: fleksibilni (možnost uvajanja manjših sprememb metode)* / Type of scope: flexible (possibility of introducing minor
modifications to the method)*
Mesto izvajanja: v laboratoriju / Site: in the laboratory
Področja preskušanja glede na vrsto preskušanja: mehansko preskušanje; fizikalno preskušanje / Testing fields with reference to the
type of test:/ mechanical testing; physical testing
Področja preskušanja glede na vrsto preskušanca: gradbeni proizvodi, materiali in konstrukcije (kamen in agregati) / Testing fields
with reference to the type of test item: construction products, materials and structures (stone and aggregates)
Št.
No.
Oznaka dokumenta,
ki opisuje metodo
preskušanja
Identification of the
document, describing the
testing method
Preskušana lastnost
oziroma parameter
Characteristic or
parameter tested
Opredelitev preskusa
(vrsta, princip oziroma
tehnika preskusa)
Description of test
(type of test, test principle or
technique)
Območje
preskušanja
Range of testing
Preskušanci
(materiali,
proizvodi)
Items tested
(materials,
products)
27. SIST EN 933-1 Zrnavost
Particle size distribution
Metoda sejanja
Sieving method
agregati
aggregates
28. SIST EN 933-4 Modul oblike
Shape index
Meritev dolžine in debeline
zrn
Particle length and
thickness measurements
agregati
aggregates
29. SIST EN 933-8 Ekvivalent peska
Sand equivalent
Merjenje višine usedline in
celotne višine suspenzije
fine frakcije v merilnem valju
Measurement the hight of
the sediment and total hight
of fine fraction suspension
in graduated cylinder
agregati
aggregates
30. SIST EN 1097-2
metoda Los Angeles
method Los Angeles
Odpornost proti drobljenju
Resistance to fragmentation
Določevanje mase
presevkov zrn s tehtanjem
pred in po drobljenju v
rotirajočem bobnu z
jeklenimi kroglami - Los
Angeles metoda
Determination of particle
mass before and after
fragmentation in rotating
drum with steel balls - Los
Angeles method
agregati
aggregates
31. SIST EN 1097-6
razen dodatek A, B in C
except annex A, B and C
Prostorninska masa zrn in
vpijanja vode
Particle density and water
absorption
Tehtanje mokrega
nasičenega agregata,
površinsko suhega agregata
in sušenega agregata
Določitev volumna s
tehtanjem košare z vzorcem
pod vodo ali s tehtanjem
piknometrov
Weighing the test portion in
the saturated, surface-dried
and oven dried condition
Determination of volume
from the mass of the water
dispaced, either by mass
reduction in the wire bascet
or by weghings in the
pycnometer
agregati
aggregates
Priloga k akreditacijski listini
Annex to Accreditation Certificate LP-008
Velja od / Valid as of 7. september 2023
Zamenjuje izdajo, veljavno od dne / Replaces the Annex valid as of 8. november 2022
Akreditacija je veljavna do preklica. Veljavnost preveriti na
This accreditation shall remain in force until withdrawn.
Information on current status available at
www.slo-akreditacija.si
Preskusni laboratorij, Špruha 18, 1236 Trzin
OB05-25 Izdaja / Revision: 8 Stran / Page: 10 / 10
Tip obsega: fleksibilni (možnost uvajanja manjših sprememb metode)* / Type of scope: flexible (possibility of introducing minor
modifications to the method)*
Mesto izvajanja: v laboratoriju / Site: in the laboratory
Področja preskušanja glede na vrsto preskušanja: mehansko preskušanje; fizikalno preskušanje / Testing fields with reference to the
type of test:/ mechanical testing; physical testing
Področja preskušanja glede na vrsto preskušanca: gradbeni proizvodi, materiali in konstrukcije (kamen in agregati) / Testing fields
with reference to the type of test item: construction products, materials and structures (stone and aggregates)
Št.
No.
Oznaka dokumenta,
ki opisuje metodo
preskušanja
Identification of the
document, describing the
testing method
Preskušana lastnost
oziroma parameter
Characteristic or
parameter tested
Opredelitev preskusa
(vrsta, princip oziroma
tehnika preskusa)
Description of test
(type of test, test principle or
technique)
Območje
preskušanja
Range of testing
Preskušanci
(materiali,
proizvodi)
Items tested
(materials,
products)
32. SIST EN 1367-2 Odpornost agregata na
vremenske vplive - MS
vrednost
Resistance to weathering -
magnesium sulfate value
Tehtanje suhega vzorca
pred in po cikličnem
namakanju v nasičeni
raztopini magnezijevega
sulfata
Weighing of dry sample
before and after cyclic
soaking in a saturated
solution of magnesium
sulphate
agregati
aggregates
*Laboratorij lahko po potrebi uvede manjše spremembe metod (npr. prilagoditev novi izdaji). Podatke o trenutnem stanju obsega vzdržuje
laboratorij in jih objavlja. / When necessary, the laboratory may introduce minor modifications to the methods (e.g. adaptation to a new version).
Data on the current status of the scope are maintained and published by the laboratory.
Opombe / Notes:
• V vseh točkah podrobnega obsega akreditacije, pri katerih v rubriki "Območje preskušanja" ni navedenih podatkov, veljajo določila
posameznih standardov oziroma drugih javno dostopnih dokumentov, ki opisujejo metodo.
In all columns of the scope of accreditation where the cells under "Range of testing" are empty, the provisions of the relevant standards or
other publicly available documents describing testing methods should apply.
• Seznam akreditiranih dejavnosti z aktualnimi podatki o dejavnostih iz fleksibilnega dela obsega laboratorij objavlja na
www.irma.si/irma_slo/pdf/LP-008.pdf v mapi Seznam akreditiranih dejavnosti.
A list of accredited activities with up-to-date information on the activities of flexible part of the scope is available on the laboratory’s website
www.irma.si/irma_slo/pdf/LP-008.pdf in the map “Seznam akreditiranih dejavnosti” (i.e. the “List of Accredited Activities”).
Datum / Date: 7.9.2023 Direktor / Director
Dr. Boštjan Godec
Kopija priloge k akreditacijski listini za objavo na spletnem mestu.
Podpisani original priloge na vpogled na sedežu SA.
Copy of Annex to the accreditation certificate for web publishing.
Signed original of Annex available for consultation at the SA head office.